Abstract:Empty Fruit Bunches (EFB) are oil palm waste that has the potential as a source of bioenergy because it contains lignocellulose (cellulose, hemicellulose, and lignin) so that it can be converted into biofuel through thermal cracking, adsorption, and distillation processes. Thermal cracking is the decomposition of the chemical content of biomass by utilizing heat without a mixture of oxygen at a temperature of 200oC–600oC. This study aims to obtain the characteristics of the raw material of EFB in the form of proximate, ultimate, lignin, and biofuel produced. The research was conducted using a thermal cracking reactor designed to control the temperature at 300oC, 350oC, 400oC, and 450oC. The results showed that the raw material characteristics of EFB from proximate were 13.66% water content, 8.74% ash content, 58.66% volatile matter and 18.90% fixed carbon. This water content is relatively high. This is because the drying process on the material has not run perfectly. The ultimate result showed that the EFB had a C content of 54.45%, H content of 5.00%, and O content of 16.27%. The atomic ratio obtained from the ultimate analysis can indicate the amount of calorific value that can be used for certain fuels. The smaller the atomic ratio value contained, the more significant the calorific value contained in a particular fuel. Klason method was carried out to decrease the level of lignin through 4 stages; the lignin content without delignification was resulting into 24.87%, the addition of aquadest was resulting into18.71%, the addition of 5% HCl resulting into 15.34%, and 10% HCl resulting into 14.49%. Delignification of 10% HCl is the pretreatment process before the thermal cracking. The thermal cracking process forms steam; the steam is then condensed to obtain bio-oil. The formed bio-oil was kept to separate the oil from tar. In order to obtain good biofuel quality, adsorption is carried out with zeolite adsorbent, which has been activated with HCL. A comparison of the physical properties of bio-oil before and after adsorption shows a color difference from brownish black to the adsorbed bio-oil, which is distilled to separate the heavy and light fractions. The temperature of 450oC at thermal cracking is close to optimum; when the temperature is increased, the cracking process will be more straightforward and occur optimally. The biofuel produced in this study was tested for its characteristics such as, density (927-1086.68 Kg/m3), kinematic viscosity (1.17-1.43 mm2/s), and flash point (66.00-70, 23oC). The biofuel product produced is dominated by C5-C15 compounds (45.07%) according to the results of GC-MS analysis.

Analysis of chemical properties for biodiesel derived from crude palm oil

Parametric study of glycerol and contaminants removal from biodiesel through solvent-aided crystallization

Characteristics of Biodiesel Produced from Crude Palm Oil through Non-Alcohol Synthesis Route Using Dimethyl Carbonate and Immobilized Eco-Enzyme Catalyst

Column Chromatography Purification and Analysis of Biodiesel by Transesterification

Glycerol Esterification of Free Fatty Acids Catalyzed by Zinc Glycerolate for Biodiesel Production from Acidified Palm Oil: Optimization, Kinetic Study, and Process Evaluation

High Vacuum Distillation for Low-Sulfur Biodiesel Production: from Laboratory to Large Scale

Natural and low-cost deep eutectic solvent for soap removal from crude biodiesel using low stirring extraction system

Optimization of crude glycerol purification from grease trap waste biodiesel production: exploring the synergistic effect of mixed extraction alcohols on enhanced glycerol purity

Improving the Cold Flow Properties of Biodiesel from Waste Cooking Oil by Surfactants and Detergent Fractionation

Ultrasound‐assisted transesterification of refined and crude palm oils using heterogeneous palm oil mill fly ash supported calcium oxide catalyst

Refinery Operation Optimization for Purification of Biodiesel Product by Alkaline-catalyzed Process

Characterization of homogenous acid catalyzed biodiesel production from palm oil: experimental investigation and numerical simulation

Investigation of high water content in bio-crude oil (BCO) produced from empty oil palm fruit bunches pyrolysis

Performance and emissions of neat crude palm oil and its emulsions as diesel engine fuel

Superiority of liquid membrane-based purification techniques in biodiesel downstream processing

Characterization Biofuel from Empty Fruit Bunch through Thermal Cracking

Experimental and numerical analysis to enhance the thermodynamic properties and biofuel stability: Sapindus mukorossi

Improvement of waste frying oil/cottonseed oil-based biodiesel properties by adjusting unsaturation and its effect on engine emission characteristics

Influence of fatty acids content in non-edible oil for biodiesel properties

Impact of Crude Oil Quality on the Refining Conditions and Composition of Nutraceuticals in Refined Palm Oil

Evaluation of Physicochemical Properties Composite Biodiesel from Waste Cooking Oil and Schleichera oleosa Oil