Abstract:Fringe patterns are typically produced as the results of traditional optical Nondestructive Evaluation (NDE) employing digital shearography. Structural flaws affect the response of the surrounding material to a certain loading, resulting in unique fringe patterns that are related to the local deformation. Smaller defect information, however, can be easily lost in the fringe pattern caused by global deformation during the flaw detection procedure. In order to improve the flaw detection capabilities of this technology, it is important to streamline the inspection process and to simplify the interpretation of the results. This study proposes a practical and effective methodology that experimentally removes fringe patterns caused by global deformation in digital shearography and only retains the defect information. For shearographic Non-Destructive Testing (NDT), two sets (3 or 4 images) of temporal phase-shifted interferograms under different loads P 1 and P 2 are recorded. This novel approach involves recording one additional set of temporal phase-shifted interferograms at a load between P 1 and P 2 , e.g. P 1' . Two phase maps of shearograms can be generated using the phase shift technique, corresponding to the two loads Δ 2 = (P 1' -P 1 ) and Δ 1 = (P 2 -P 1 ), respectively. Because of the nondestructive nature of the testing, the magnitude of the loads P 1 and P 2 is small, and the 1st derivative of global deformation in the shearing direction of the test part is assumed to be linear. Therefore, a linear coefficient C based on the two shearograms can be determined. The information from global deformation is then removed by subtracting the shearogram generated with the small load Δ 2 multiplied by the correlation coefficient C from the one obtained with the relatively large load Δ 1 . This technique is further improved by calculating a complete surface linear coefficient C ij , which improves the detail processing of the deformation of samples with complex geometry and mechanical properties. This technique is shown to effectively assess a wide range of structures, including aluminum specimens with prepared flaws and intricate composite laminates. The experimental findings demonstrate that the suggested technique improves the non-destructive testing capabilities of digital shearography, thereby simplifying defect detection and visualization.

In-situ real-time imaging of subsurface damage evolution in carbon fiber composites with shearography

Method for Visualizing the Shear Process of Rock Joints Using 3D Laser Scanning and 3D Printing Techniques

Defect imaging in carbon fiber composites by acoustic shearography

Morphology characterization and in-situ three-dimensional strain field monitor of short carbon fiber-reinforced polymer composites under tension

Infrared-Induced Laser Shearography: Enhanced Multimodal Features Recognition for Interfacial Defects in SIR/GFRP Composite Structures

Observation of Damage Initiation for Trans-laminar Fracture Using in situ Fast Synchrotron X-ray Radiography and ex situ X-ray Computed Tomography

Acoustic Emission Characterization of Damage Patterns in Composite Scarf Joints Using Unsupervised Learning

Inspection of defects in composite structures using long pulse thermography and shearography

3D photothermal reconstruction of subsurface defects in notched multidirectional CFRP laminates due to tensile fatigue loading

Real-time self-monitoring and smart bend recognizing of fiber-reinforced polymer composites enabled by embedded magnetic fibers

Questioning the Representativeness of Damage Mechanisms in Single‐Fiber Composites via In Situ Synchrotron X‐Ray Holo‐Tomography

Review of Self-Sensing of Damage and Interfacial Evaluation Using Electrical Resistance Measurements in Nano/micro Carbon Materials-Reinforced Composites

Microscopic Progressive Damage And Failure Analysis Of Carbon-Fiber Reinforced Composite Under Shear Loading

Characterisation of damage evolution in plain weave SiC/SiC composites using in situ X-ray micro-computed tomography

A Study on Damage of T800 Carbon Fiber/Epoxy Composites under In-Plane Shear Using Acoustic Emission and Digital Image Correlation

Direct observation of the morphological changes in a carbon fiber composite by means of in-situ micro-CT compression experiment

Ultrasound tomography for health monitoring of carbon fibre–reinforced polymers using implanted nanocomposite sensor networks and enhanced reconstruction algorithm for the probabilistic inspection of damage imaging

Nondestructive evaluation of carbon-fiber composites using digital image correlation, acoustic emission, and optical based modal analysis

Structural Health Monitoring of Glass Fiber-Reinforced Polymer Laminates with Carbon Nanotube-Coated Glass Fiber Sensing Layer after Low-Velocity Impact Using Electrical Resistance Tomography

Digital shearography for NDT: Study on a novel experiment based method for removing global deformation ✰

Detecting damage in composites using volume decomposition analysis of tomographic data