Abstract:Hydroxyl-terminated polybutadiene (HTPB) is a flexible telechelic compound with a main chain containing a slightly cross-linked activated carbon-carbon double bond and a hydroxyl group at the end. Therefore, in this paper, HTPB was used as a terminal diol prepolymer, and sulfonate AAS and carboxylic acid DMPA were used as hydrophilic chain extenders to prepare low-temperature adaptive self-matting waterborne polyurethane (WPU). Due to the fact that the non-polar butene chain in the HTPB prepolymer cannot form a hydrogen bond with the urethane group, and the solubility parameter difference between the hard segment formed by the urethane group is large, the gap of T g between the soft and hard segments of the WPU increases by nearly 10 °C, with more obvious microphase separation. At the same time, by adjusting the HTPB content, WPU emulsions with different particle sizes can be obtained, thereby obtaining WPU emulsions with good extinction properties and mechanical properties. The results show that HTPB-based WPU with a certain degree of microphase separation and roughness obtained by introducing a large number of non-polar carbon chains has good extinction ability, and the 60° glossiness can be as low as 0.4 GU. Meanwhile, the introduction of HTPB can improve the mechanical properties and low temperature flexibility of WPU. The T g,s (the glass transition temperature of soft segment) of WPU modified by the HTPB block decreased by 5.82 °C, and the ΔT g increased by 21.04 °C, indicating that the degree of microphase separation increased. At -50 °C, the elongation at break and tensile strength of WPU modified by HTPB can still maintain 785.2% and 76.7 MPa, which are 1.82 times and 2.91 times those of WPU with only PTMG as soft segment, respectively. The self-matting WPU coating prepared in this paper can meet the requirements of severe cold weather and has potential application prospects in the field of finishing.

Bonding of rubber to steel: Effects of hydroxyl-terminated polybutadiene on the adhesion of waterborne polyurethane adhesives

Modification of Unsaturated Polyester Resin by HTPB: Effect of Introducing Method of the Rubber

Preparation and Properties of Epoxided Hydroxyl-terminated Polybutadiene Based Polyurethane Elastomers

Modeling the Interfacial De-Bonding Behavior Between Steel Wire and Adhesive

Synthesis and Evaluation of Polyurethane as Waterproof Adhesion Layer for Steel Bridge Deck

Synthesis and characterization of hydroxyl-terminated polybutadiene modified low temperature adaptive self-matting waterborne polyurethane

Adhesion Mechanisms Between Steel and Polyethylene Modified by Nanoparticles

A Humidity‐Insensitive Waterborne Polyurethane Pressure‐Sensitive Adhesive Modified by Castor Oil and Siloxane

Enhancing Interface Adhesion Between Waterjet‐produced Rubber Powders and Natural Rubber by Wet‐mixing Method

Promoters for Improved Adhesion Strength between Addition-Cured Liquid Silicone Rubber and Low-Melting-Point Thermoplastic Polyurethanes

Interface Bonding Properties and Mechanism of Steel Fiber and Hot Melt Adhesive via Interface Design Engineering

Novel rubber-steel adhesive based on resole phenol formaldehyde/unsaturated polyester/soybean oil polyol blends with high thermal stability performance

Enhanced Mechanical and Dielectric Properties of an Epoxy Resin Modified with Hydroxyl-Terminated Polybutadiene

Rational Design of Waterborne Polyurethane Pressure Sensitive Adhesives for Different Working Temperatures

Silicone‐containing polyurea elastomer possessing main‐chain boron–oxygen bonds with delayed stress relaxation and improved adhesive properties

Castor oil-based polyurethane adhesives: Effect of cross-linker on the bond strength

Copolymerization approach of soft segment towards the adhesion improvement of polycarbonate-based thermoplastic polyurethane

Studies on the mechanism of adhesion of polyurethane to polyvinylchloride

Polymer Blends of Pbt and Pp Compatibilized by Epoxidized Ethylene Propylene Diene Rubber

Strong Dynamic Interfacial Adhesion by Polymeric Ionic Liquids under Extreme Conditions

Improving Adhesion of Silicone Rubber Coating to Polyurethane Surface