Abstract:In this study, a novel perovskite solar cell (PSC) architecture is presented that utilizes an HTL-free configuration with formamide tin iodide (FASnI3) as the active layer and fullerene (C60) as the electron transport layer (ETL), which represents a pioneering approach within the field. The elimination of hole transport layers (HTLs) reduces complexity and cost in PSC heterojunction structures, resulting in a simplified and more cost-effective PSC structure. In this context, an HTL-free tin HC(NH2)2SnI3-based PSC was simulated using the solar cell capacitance simulator (SCAPS) within a one-dimensional framework. Through this approach, the device performance of this novel HTL-free FASnI3-based PSC structure was engineered and evaluated. Key performance parameters, including the open-circuit voltage (Voc), short-circuit current density (Jsc), fill factor (FF), power conversion efficiency (PCE), I-V characteristics, and quantum efficiency (QE), were systematically assessed through the modulation of physical parameters across various layers of the device. A preliminary analysis indicated that the HTL-free configuration exhibited improved I-V characteristics, with a PCE increase of 1.93% over the HTL configuration due to improved electron and hole extraction characteristics, reduced current leakage at the back contact, and reduced trap-induced interfacial recombination. An additional boost to the device's key performance parameters has been achieved through the further optimization of several physical parameters, such as active layer thickness, bulk and interface defects, ETL thickness, carrier concentration, and back-contact materials. For instance, increasing the thickness of the active layer PSC up to 1500 nm revealed enhanced PV performance parameters; however, further increases in thickness have resulted in performance saturation due to an increased rate of hole-electron recombination. Moreover, a comprehensive correlation study has been conducted to determine the optimum thickness and donor doping level for the C60-ETL layer in the range of 10-200 nm and 1012-1019 cm-3, respectively. Optimum device performance was observed at an ETL-C60 ultra-thin thickness of 10 nm and a carrier concentration of 1019 cm-3. To maintain improved PCEs, bulk and interface defects must be less than 1016 cm-3 and 1015 cm-3, respectively. Additional device performance improvement was achieved with a back-contact work function of 5 eV. The optimized HTL-free FASnI3 structure demonstrated exceptional photovoltaic performance with a PCE of 19.63%, Voc of 0.87 V, Jsc of 27.86 mA/cm2, and FF of 81%. These findings highlight the potential for highly efficient photovoltaic (PV) technology solutions based on lead-free perovskite solar cell (PSC) structures that contribute to environmental remediation and cost-effectiveness.

Wide-bandgap Cesium-Formamidinium-Based Perovskite for Possible Indoor Applications: TCAD Simulation Study

High Performance Inverted RbCsFAPbI3 Perovskite Solar Cells Based on Interface Engineering and Defects Passivation.

Key Parameters and Thresholds Values for Obtaining High Performance Perovskite Solar Cells Indoors from Full Br Compositional and Bandgap Engineering

Stable Cesium-Rich Formamidinium/Cesium Pure-Iodide Perovskites for Efficient Photovoltaics

Numerical Simulation and Optimization of Highly Stable and Efficient Lead-Free Perovskite FA1−xCsxSnI3-Based Solar Cells Using SCAPS

Unveiling the Potential of Cs3Sb2ClxI9‐x‐Based Solar Cells for Efficient Indoor Light Harvesting: Numerical Simulation

Efficient and Stable Wide‐Bandgap Perovskite Solar Cells Derived from a Thermodynamic Phase‐Pure Intermediate

Toward high efficiency for long-term stable Cesium doped hybrid perovskite solar cells via effective light management strategy

Stable Cesium Formamidinium Lead Halide Perovskites: A Comparison of Photophysics and Phase Purity in Thin Films and Single Crystals

Trivalent Europium Doped CsCl Quantum Dots for MA‐free Perovskite Solar Cells with Inherent Bandgap through Lattice Strain Compensation

Energy Level Alignment Regulation and Carrier Management in Perovskite Solar Cells with Various Bandgaps Using Tailored Metal‐Organic Frameworks

Engineering the Non‐Radiative Recombination of Mixed‐Halide Perovskites with Optimal Bandgap for Indoor Photovoltaics

Interfacial Energy Level Tuning for Efficient and Thermostable CsPbI2Br Perovskite Solar Cells

Amide‐Catalyzed Phase‐Selective Crystallization Reduces Defect Density in Wide‐Bandgap Perovskites

Ion‐Dipole Interaction Enabling Highly Efficient CsPbI3 Perovskite Indoor Photovoltaics

A Facile Low Temperature Fabrication of High Performance CsPbI2Br All‐Inorganic Perovskite Solar Cells

Advanced Optoelectronic Modeling and Optimization of HTL-Free FASnI3/C60 Perovskite Solar Cell Architecture for Superior Performance

Performance optimization of phenylethylammonium-formamidinium tin iodide perovskite solar cell by contrasting various ETL and HTL materials

Enhanced Efficiency and Stability of Wide‐Bandgap Perovskites via Br‐Rich Bulk and Surface 2D Passivation for Indoor Photovoltaics

Design and simulation of CsPb.625Zn.375IBr2-based perovskite solar cells with different charge transport layers for efficiency enhancement

Vertical Phase Separated Cesium Fluoride Doping Organic Electron Transport Layer: A Facile and Efficient “bridge” Linked Heterojunction for Perovskite Solar Cells