Abstract:The biggest obstacle to the widespread implementation of polymer electrolyte membrane fuel cells (PEMFCs) is their cost, primarily due to the use of platinum catalysts. The high intrinsic catalyst activity exhibited on a rotating disk electrode (RDE) is rarely realized in a membrane electrode assembly (MEA), which is a long-standing challenge for PEMFCs and a cause of low catalyst utilization. To translate the high RDE performance of a catalyst into a MEA, the design of an ideal ionomer/catalyst interface is proposed: a thin, conformal ionomer film covers the maximum surface of a Pt nanoparticle and thus simultaneously maximizes catalyst utilization, ( i.e. , high mass activity and electrochemically active surface area) and O 2 diffusion rate ( i.e. , high current density performance) without compromising proton conduction. Building such an interface is a long-standing challenge due to the lack of interaction between the ionomer and catalyst particles, resulting in large ionomer agglomerates and inhomogeneous ionomer coverage over the catalyst nanoparticle, with consequent poor fuel cell performance. In this work, this ionomer/catalyst interface has been engineered, utilizing the electrostatic attraction between positively charged catalyst and negatively charged ionomer particles in a catalyst ink and preserved in a solid catalyst layer. As a result, this interface leads to previously unachieved proton exchange membrane fuel cell performance in terms of both catalyst utilization (75% vs. 45%) and peak/rated power density ( i.e. , 1.430/0.930 W cm −2 , H 2 /air, cathode Pt loading: 0.1 mg Pt cm −2 ) for pure Pt catalysts, even better than those of Pt alloy catalysts. This work demonstrates the formation of an interface in the liquid phase (using ultra-small-angle X-ray scattering in combination with cryo-TEM, isothermal–titration–calorimetry) and the preservation of the interface in the solid catalyst layer (using TEM) and estimates the effective coverage and thickness of the ionomer film (using limiting current density, RDE and fuel cell performance).

Heterogeneous Catalytic Reactor for Hydrogen Production from Formic Acid and Its Use in Polymer Electrolyte Fuel Cells

Reshaping the Cathodic Catalyst Layer for Anion Exchange Membrane Fuel Cells: from Heterogeneous Catalysis to Homogeneous Catalysis

Construction of Homogeneous Catalyst Layers at Proton Exchange Membrane Fuel Cell Cathodes

Computational Studies on Microreactors for the Decomposition of Formic Acid for Hydrogen Production Using Heterogeneous Catalysts

Concurrent electrocatalytic hydrogen evolution and polyethylene terephthalate plastics reforming by self-supported amorphous cobalt iron phosphide electrode

Bimetallic AgPd Nanoparticles Immobilized on Amine‐Functionalized SBA‐15 As Efficient Catalysts for Hydrogen Generation from Formic Acid

Computational Investigation of Microreactor Configurations for Hydrogen Production from Formic Acid Decomposition Using a Pd/C Catalyst

Continuous hydrogen production from liquid-phase formic acid dehydrogenation over Pd/AC catalysts: a kinetic study

Chromic hydroxide-decorated palladium nanoparticles confined by amine-functionalized mesoporous silica for rapid dehydrogenation of formic acid

Dehydrogenation of Formic Acid at Room Temperature: Boosting Palladium Nanoparticle Efficiency by Coupling with Pyridinic‐Nitrogen‐Doped Carbon

Suppression of the Hydrogen Evolution Reaction Is the Key: Selective Electrosynthesis of Formate from CO2 over Porous In55Cu45 Catalysts

Single-Site Ruthenium Pincer Complex Knitted into Porous Organic Polymers for Dehydrogenation of Formic Acid

Production of performic acid through a capillary microreactor by heterogeneous catalyst

Pd nanocatalyst supported on amine-functionalized mesoporous graphitic carbon nitride for formic acid hydrogen generator in the polymer electrolyte membrane fuel cell system

Hydrogen Evolution from Additive-Free Formic Acid Dehydrogenation Using Weakly Basic Resin-Supported Pd Catalyst

Carbon gel-derived Fe–N–C electrocatalysts for hydrogen-air polymer electrolyte fuel cells

Unraveling the core of fuel cell performance: engineering the ionomer/catalyst interface

A composite proton exchange membrane with three-dimensionally-reinforced hydrogen bonding network for durable hydrogen fuel cells

Bis-imidazolium Pd(0) based supported catalyst for the selective dehydrogenation of formic acid

(Invited) Catalyst Layers for Fluorine-Free Hydrocarbon PEMFCs

The Gas Diffusion Electrode Setup as Straightforward Testing Device for Proton Exchange Membrane Water Electrolyzer Catalysts