Abstract:Single hat sectioned hybrid beams composed of aluminum and Carbon Fiber Reinforced Polymeric materials (CFRP), intended for structural applications in the automotive and aviation sectors, have been studied from the point of their energy absorption capabilities when submitted to transverse low-velocity impact loading. Carbon fiber-epoxy composite prepregs were placed on the inside of the single hat sectioned aluminum sheet and completely cured in the autoclave under the recommended curing cycle. The bonding process between the aluminum sheet and composite layers was achieved by using 3M VHB™ 4930 double-sided acrylic foam tape. Bonding the aluminum and composite layers through adhesive tape eliminates the requirement of surface preparation of the aluminum layer through chemical etching or mechanical abrasion and thereby the strength of the metallic layer is not reduced due to the formation micropores during the chemical etching process. Results are shown in terms of load-displacement and damage morphologies diagrams; characteristic trends are compared and discussed. It was observed that the presence of viscoelastic adhesive tape material restricts the rupture (visual cracks) failure of the outer aluminum layer, resulting in the only impact-induced indentation for all impact energies. Numerical simulations were also performed to characterize and predict the failure mechanism of such hybrid beams when subjected to impact loading. Numerical predictions showed good correlation with experimental results for all impact histories at low and medium impact energies but a showed slight discrepancy for highest impact energy and were not able to successfully capture the system response in the unloading region. Current modeling does not consider damage healing or recovery with unloading and it is difficult to account for such change in material state. This study provides the low-velocity impact characteristics and collapse behavior of the hybrid hat sectioned beams under tensile and shear forces developed by impact loading by providing insight to their primary damage mechanisms relative to the impact energies. It was found that the primary damage of the specimen's changes from impact-induced indentation, minimal fiber breakage to partial perforation accompanied by larger indentation depth as the impact energy is increased from 6 to 12 J.

Experimental and numerical study on the high-velocity hail impact performance of carbon fiber aluminum alloy laminates

Progressive Damage Behaviour Analysis and Comparison with 2D/3D Hashin Failure Models on Carbon Fibre-Reinforced Aluminium Laminates

Numerical Simulation of Low Velocity Impact Failure of CCF300 Carbon Fiber Laminate Based on ABAQUS

Study of Low-Velocity Impact Behavior of Hybrid Fiber-Reinforced Metal Laminates

Experimental and numerical investigation on high-velocity hail impact response of TC4 titanium alloy plates

Experimental and Simulation Study on Failure of Thermoplastic Carbon Fiber Composite Laminates under Low-Velocity Impact

Study of the dynamic response and damage evolution of carbon fiber/ultra-thin stainless-steel strip fiber metal laminates under low-velocity impact

Low-Velocity Impact Behavior and Damage Characteristics of CFRP Laminates

Experimental and numerical characterization of flexural properties and failure behavior of CFRP/Al laminates

Residual Compressive Strength of Aluminum Honeycomb Sandwich Structures with CFRP Face Sheets after Low-velocity Impact

Experimental investigation on the compression‐after‐double‐impact behaviors of GFRP laminates embedded with aluminum mesh

Experimental and numerical investigations on the dynamic response of woven carbon fiber reinforced thick composite laminates under low-velocity impact

Corrosion damage evolution and mechanical properties of carbon fiber reinforced aluminum laminate

Low‐velocity multiple impact damage characteristics and numerical simulation of carbon fiber/epoxy composite laminates

Low Velocity Impact Response of Carbon Fiber Composite Laminates with Surface Glass Fibers

The Correlation of LVI Parameters and CAI Behaviour in Aluminium-Based FML

Finite element analysis of dynamic progressive failure properties of GLARE hybrid laminates under low-velocity impact

An experimental study of the dynamic responses of carbon fiber reinforced polymer composite laminates subjected to ice impact

A Numerical Study of Blast Resistance of Carbon Fiber Reinforced Aluminum Alloy Laminates

Low-Velocity Impact Characteristics of Hybrid Aluminum/CFRP Single Hat Sectioned Beam Adhesively Bonded Using Adhesive Tape

An Efficient Numerical Method to Analyze Low‐velocity Impact Response of Carbon Fiber Reinforced Thermoplastic Laminates