Abstract:Abstract This paper presents 3D Fabry–Pérot (FP) cavities fabricated directly onto cleaved ends of low-loss optical fibers by a two-photon polymerization (2PP) process. This fabrication technique is quick, simple, and inexpensive compared to planar microfabrication processes, which enables rapid prototyping and the ability to adapt to new requirements. These devices also utilize true 3D design freedom, facilitating the realization of microscale optical elements with challenging geometries. Three different device types were fabricated and evaluated: an unreleased single-cavity device, a released dual-cavity device, and a released hemispherical mirror dual-cavity device. Each iteration improved the quality of the FP cavity’s reflection spectrum. The unreleased device demonstrated an extinction ratio around 1.90, the released device achieved 61, and the hemispherical device achieved 253, providing a strong signal to observe changes in the free spectral range of the device’s reflection response. The reflectance of the photopolymer was also estimated to be between 0.2 and 0.3 over the spectrum of interest. The dual-cavity devices include both an open cavity, which can interact with an interstitial medium, and a second solid cavity, which provides a static reference reflection. The hemispherical dual-cavity device further improves the quality of the reflection signal with a more consistent resonance, and reduced sensitivity to misalignment. These advanced features, which are very challenging to realize with traditional planar microfabrication techniques, are fabricated in a single patterning step. The usability of these FP cavities as thermal radiation sensors with excellent linear response and sensitivity over a broad range of temperature is reported. The 3D structuring capability the 2PP process has enabled the creation of a suspended FP heat sensor that exhibited linear response over the temperature range of 20 oC –120 oC; temperature sensitivity of ∼50 pm oC −1 at around 1550 nm wavelength; and sensitivity improvement of better than 9x of the solidly-mounted sensors.

Fabrication of a Fabry-Pérot dielectric filter with sub-nanometer narrow bandwidth

Narrow band filters in both transmission and reflection with metal/dielectric thin films

Study of tunable Fabry-Perot filter based on piezoelectric polymer film

Fabrication and Analysis of a Fabry-Perot Cavity with a Micromechanical Wet-Etching Process.

Omnidirectional Narrow Bandpass Filter Based on Metal-Dielectric Thin Films

Novel Method of Fabricating Fabry-Perot Cavity Employing MEMS Wet-Etching Process

Tunable, Ultra-Narrow-Band Optical Filter Based on A Whispering Gallery Mode Hybrid-Microsphere

Near-infrared Narrow-Band Minus Filter Based on a Mie Magnetic Dipole Resonance

All-Dielectric Color Filter with Ultra-Narrowed Linewidth

Narrow-Band Add-Drop Filter Based on Phase-Modulated Grating-Assisted Contra-Directional Couplers

Quickly tunable ultra-narrow filter via a metal film waveguide

Free-spectral-range-free Filters with Ultrawide Tunability Across the S + C + L Band

A Compact Self-Injection-Locked Narrow-Linewidth Diode Laser with Narrowband Dielectric Filter

Non-polarized and Ultra-Narrow Band Filter in MIR Based on Multilayer Metasurface

Three-dimensional Fabry–Pérot cavities sculpted on fiber tips using a multiphoton polymerization process

Terahertz narrow bandpass filters based on double-layer metallic woven meshes with engineered Fabry-Perot cavities

Narrow Linewidth Terahertz Filter Based on Gold-Coated Polymer Plates With Corrugations

Lithium Niobate Piezoelectric Actuator-Integrated Fiber Fabry-Pérot Tunable Filter with Ultrahigh Speed and Linearity

Compact optical short-pass filters based on microfibers.

Novel 6‐GHz/80.8% fractional bandwidth filtering power divider with ultra‐large coupling coefficient using air‐dielectric broadside‐coupled lines

Narrowband wide dynamic range tunable filter based on Fano resonant planar multilayered structure