Abstract:Around 8% of the global carbon dioxide emissions, are generated during cement manufacturing, which also involves significant use of raw materials, leading to adverse environmental effects. Consequently, extensive research is being conducted worldwide to explore the feasibility of utilizing different industrial waste by-products as alternatives to cement in concrete production. Fly ash (FA), Metakaolin (MK), Silica fume (SF), and ground granulated blast furnace slag (GGBS) are potential industrial materials that can serve as cement substitutes in pervious concrete. However, there exist conflicting findings in the literature regarding the impact of industrial supplementary cementitious materials (ISCMs) as partial cement replacements on the physical, mechanical, and durability properties of pervious concrete. The aim of this review is to investigate the feasibility and potential benefits of using ISCMs and compare them as partial cement replacements in the production of pervious concrete. The analysis primarily examines the effect of ISCMs as partial cement replacements on cementitious properties, including properties of ISMCs, mechanical properties, and durability of pervious concrete. The influence of ISCMs primarily stems from their pozzolanic reaction and filler characteristics. SF has the highest reactivity due to its high surface area and amorphous structure, resulting in a rapid pozzolanic reaction. GGBS and FA have moderate reactivity, while MK has relatively low reactivity due to its crystalline structure. Results from various studies indicate that the addition of FA, SF, and MK up to approximately 20% leads to a reduction in porosity and permeability while improving compressive strength and durability due to the filler effect of SF and MK. Incorporating GGBS increases permeability slightly while causing a slight decrease in compressive strength. The range of permeability and compressive strength for pervious concrete incorporating FA, SF, GGBS and MK were 0.17-1.46 cm/s and 4-35 MPa, 0.56-2.28 cm/s and 3.1-35 MPa, 0.19-0.64 cm/s and 8-42 MPa, 0.10-1.28 cm/s and 5.5-41 MPa, respectively, which are in the acceptable range for non-structural application of pervious concrete. In conclusion, it is possible to produce sustainable pervious concrete by substituting up to 20% of cement with FA, SF, GGBS, and MK, thereby reducing cement consumption, carbon footprint, energy usage, and air pollution associated with conventional cement production. However, further research is required to systematically assess the durability properties, long-term behavior, and, develop models for analyzing CO2 emissions and cost considerations of pervious concrete containing ISMCs.

Greener cementitious composites incorporating sewage sludge ash as cement replacement: A review of progress, potentials, and future prospects

Understanding the Role of Calcium Silicate Slag in Sodium Carbonate-Activated Green Materials: Influence on Kinetics, Strength, and Efflorescence

Effect of sewage sludge ash on mechanical properties, drying shrinkage and high-temperature resistance of cement mortar

Recycling use of sulfate-rich sewage sludge ash (SR-SSA) in cement-based materials: Assessment on the basic properties, volume deformation and microstructure of SR-SSA blended cement pastes

Influence of Cement Replacement with Sewage Sludge Ash (SSA) on the Heat of Hydration of Cement Mortar

3D printed concrete with sewage sludge ash: Fresh and hardened properties

Substitution of sewage sludge ash for sand in concrete containing sintered coarse aggregate: A lightweight concrete with fully solid waste aggregate

Studying the effectiveness of sewage sludge ash and its combination with natural pozzolans in controlling alkali–silica reaction

Sustainable utilization of sewage sludge ash in stabilizing subgrade soil: an appraisal

Enhanced immobilization of metal pollutants in sewage sludge ash (SSA)-cement pastes by calcium chloride and nitrate: Experimental and DFT studies

Utilization of Sintered Sludge Ash with Different Mechanical–Thermal Activation Parameters as a Supplementary Cementitious Material: Mechanical Properties and Life Cycle Assessment of Cement-Based Paste

Utilization of sewage sludge ash in ultra-high performance concrete (UHPC): Microstructure and life-cycle assessment

A Review on Cementitious and Geopolymer Composites with Lithium Slag Incorporation

A review of utilization of industrial waste materials as cement replacement in pervious concrete: An alternative approach to sustainable pervious concrete production

Optimization of eco-friendly materials by alkali activation of the sewage sludge ash (SSA) to reduce carbon footprint

Partial Replacement of Cement with Different Wastes - A Review

Effect of Biochar and Sewage Sludge Ash as Partial Replacement for Cement in Cementitious Composites: Mechanical, and Durability Properties

Effective reutilization of textile sludge from common effluent treatment plant with mineral admixture as a partial replacement for cement in mortar mixes

Modification of Concrete Composition Doped by Sewage Sludge Fly Ash and Its Effect on Compressive Strength

A Novel Approach for the Synthesis of Eco-friendly Geopolymer Ternary Blended Mortar with GGBS, Sugarcane Bagasse Ash, and Sewage Sludge Ash under Ambient Curing Conditions

Strength and Durability Characteristics of Cement Composites with Recycled Water and Blast Furnace Slag Aggregate