Abstract:In order to promote the application of LIBS technology in electrolytic aluminum industry, give full play to its advantages of rapidness, no preparation and multi-element simultaneous detection. The contents of Fe and Si elements in general aluminium procuced from electrolysis process were detected by means of laser induced breakdown for the first time, and the reasonable experimental conditions were explored, the calibration curves were established and the content of Fe and Si in general aluminium were quantitatively analyzed based on reasonable experimental conditions. The accuracy of LIBS measurement results were examined according to national standard GB / T 7999-2015 "optical emission spectrometric analysis method of aluminum and aluminum alloy". The fundamental frequency 1 064 nm laser produced by Nd : YAG pulsed laser device as the excitation source producing plasma, the spectral informations were detected and recorded by multi-channel grating spectrometer and ICCD detector. First of all, LIBS spectral line was detected and the spectral line was assigned, the line of Al I 266. 04 nm, Si I 288. 15 nm and Fe I 259. 92 nm were selected for quantitative analysis through comprehensive consideration. The influence of trigger delay time, 1Q delay time, laser setting voltage on the spectral signal intensity and SNR were researched respectively in the paper. The experimental results show that the trigger delay time of 4 mu s, 1Q delay time of 170 similar to 190 is, the laser set voltage of 560 V are the reasonable experimental parameters for Si and Fe element quantitative analysis in this paper. According to the relationship between spectral intensity and elemental concentration, the calibration curves were cestablished by the internal standard method. The correlation coefficients were 0. 952 11 and 0. 919 72, and the relative standard deviation were 6. 34% and 7. 25% for Fe and Si elements respectively. There was a good linear relationship between concentration and spectral intensity, and the 12 samples were quantitatively analyzed base on the above model. The relative error of Fe content is 0 similar to 17. 3% and the relative error of Si content is 0 similar to 14. 3% compared with the results obtained by OES. The measurement results 100% comply with the allowable requirements for Si content in 12 samples, and the results 91. 7% meet the allowable difference requirements according to national atandard GB/T 7999-2015 "optical emission spectrometric analysis method of aluminum and aluminum alloy". The experimental results show that, LIBS technology has a certain value of promotion and using in the electrolytic aluminum industry for Fe and Si elements detection.

High-repetition rate acousto-optic gated SAF-LIBS for quantitative analysis

Optical Scanning Analysis of Static Samples by Compact Laser Induced Breakdown Spectroscopy

Accuracy Improvement of Single-Sample Calibration Laser-Induced Breakdown Spectroscopy with Self-Absorption Correction

A Method for Improving the Accuracy of Calibration-Free Laser-Induced Breakdown Spectroscopy by Exploiting Self-Absorption.

Self-absorption Correction Method for One-Point Calibration Laser-Induced Breakdown Spectroscopy.

Ultra-simplified design and quantitative analysis for the optical system of compact laser-induced breakdown spectroscopy

Accurate Quantitative Analysis of LIBS With Image Form Spectra by Using a Hybrid Deep Learning Model of a Convolutional Block Attention Module-Convolutional Neural Network-Long Short-Term Memory

Performance improvement of underwater LIBS qualitative and quantitative analysis by irradiating with long nanosecond pulses.

An Echellograms-Based Quantitative Analysis Method of Laser-Induced Breakdown Spectroscopy

Spectral Interference Elimination and Self-Absorption Reduction in Laser-Induced Breakdown Spectroscopy Assisted with Laser-Stimulated Absorption

Research on Batch Multielement Rapid Quantitative Analysis Based on the Standard Curve-Assisted Calibration-Free Laserinduced Breakdown Spectroscopy Method

Sensitivity improvement in the measurement of minor components by spatial confinement in fiber-optic laser-induced breakdown spectroscopy

Accuracy improvement of quantitative analysis in spatially resolved fiber-optic laser-induced breakdown spectroscopy

Development of a Compact Synchronizer for Laser-Induced Breakdown Spectroscopy

Investigation on Experimental Conditions and Quantitative Analysis for Fe and Si Elements in General Aluminum by Laser Induced Breakdown Spectroscopy Technique

Spectral enhancement and quantitative accuracy improvement of trace metal elements in aqueous solutions using electrostatic-assisted laser-induced breakdown spectroscopy

Quantitative Analysis method of laser-induced breakdown spectroscopy based on temperature iterative correction of self-absorption effect

A Spectral Standardization Method Based on Plasma Image-Spectrum Fusion to Improve the Stability of Laser-Induced Breakdown Spectroscopy

Self-absorption Reduction in Laser-Induced Breakdown Spectroscopy Using Laser-Stimulated Absorption

Improving signal stability and analysis accuracy in laser-induced breakdown spectroscopy by multi-directional collection

Investigation of the self-absorption effect using time-resolved laser-induced breakdown spectroscopy.