Abstract:Poly(L-lactide) (PLLA) has been receiving attention as a material for bone fixation devices because of its good biocompatibility and biodegradability. However, its mechanical properties are weaker than those of natural bone. Interestingly, solid-state extrusion can enhance the mechanical properties by orienting the polymer chains, and molecular weight is one of the key factors in this process. In this study, we optimized the heating conditions for vacuum compression molding to make a PLLA block for the solid-state extrusion process. We confirmed that the molecular weight of the material decreased with increasing heating temperature and time. In the case of a low molecular weight such as 120 kDa, the heating temperature and time were optimized to 190 oC and 90 min, respectively. Moreover, we fabricated a plate, a rod, and a square pole of PLLA by solid-state extrusion for the development of a bone plate, a screw, and an interbody cage. PLLA plates having various molecular weights (150-250 kDa) were extruded to various draw ratios to investigate the effect of molecular weight on the solid-state extrusion process. The mechanical properties such as flexure stress and flexure modulus increased with increasing draw ratio, which in turn increased with increasing molecular weight of the polymer. In addition, we determined that the crystallinity of PLLA dramatically increased when the draw ratio was more than 4. In addition, the orientation of the crystals by solid-state extrusion was confirmed by using X-ray diffraction, and the orientation effect increased with increasing draw ratio of the extruded PLLA. PLLA plates made by solid-state extrusion could be manufactured into bone plates. Furthermore, we fabricated a PLLA rod by solid-state extrusion and vacuum compression molding. The flexural properties of the extruded rod were better than those of the molded rod. We could, therefore, fabricate a screw using the extruded PLLA rod. Finally, interbody cages were made by using poly(L,D/L-lactide) (PLDLLA), PLLA of various molecular weights (150-250 kDa), and PLLA enhanced by solid-state extrusion. The results of the compression tests indicated that PLLA was generally stronger than PLDLLA and that the extruded PLLA had the best mechanical properties. Consequently, it is possible to successfully manufacture biodegradable spinal fixation devices, including plates, screws, and interbody cages, by solidstate extrusion. Moreover, their mechanical properties could be improved by increasing the draw ratio and molecular weight.

Mechanical characteristics and in vitro degradation kinetics analysis of polylactic glycolic acid/β-tricalcium phosphate (PLGA/β-TCP) biocomposite interference screw

Mechanical Properties and Degradation Properties in Vitro of Carbon Fiber Reinforced Hydroxyapatite/polylactide Composite

A biodegradable, osteo-regenerative and biomechanically robust polylactide bone screw for clinical orthopedic surgery

[Preliminary Evaluation of the Biological Properties of Poly-Lactide-co-glycolic Acid (PLGA) Knitted Mesh].

“Polylactic acid-polyethylene glycol-hydroxyapatite composite” an efficient composition for interference screws

In vitro degradation of self‐reinforced poly(lactic acid) with beta‐tricalcium phosphate composite prepared by equal channel angular pressing

Mechanical properties and biomedical application characteristics of degradable polylactic acid–Mg–Ca3(PO4)2 three-phase composite

Poly(l,l-lactide-co-glycolide)/tricalcium Phosphate Composite Scaffold and Its Various Changes During Degradation in Vitro

Structure, Properties, and in Vitro Degradation Behavior of Biodegradable Poly(l‐lactic Acid)‐trimethylene Carbonate‐glycolide Terpolymer

Enhanced biocompatibility of PLGA nanofibers with gelatin/nano-hydroxyapatite bone biomimetics incorporation.

Experimental Research on Degradation and Biocompatibility of Super-high-molecular-weight Poly-DL-lactic Acid

Development of a novel PLDLA/β-TCP composite-based biodegradable anterior cervical plate and screw system

In Vivo Degradation Studies of PGA-PLA Block Copolymer and Their Histochemical Analysis for Spinal-Fixing Application

A programmable, fast-fixing, osteo-regenerative, biomechanically robust bone screw

[Tissue Reaction and Degradation of Super-High Molecular Weight Poly D, L-lactic Acid Mini-Plates and Screws: an Animal Experiment].

Characterization of degradation kinetics of additively manufactured PLGA under variable mechanical loading paradigms

Morphology, thermal properties, mechanical property and degradation of PLGA/PTMC composites

Strontium-Substituted Nanohydroxyapatite-Incorporated Poly(lactic acid) Composites for Orthopedic Applications: Bioactive, Machinable, and High-Strength Properties

In vitro and in vivo evaluation of polylactic acid-based composite with tricalcium phosphate microsphere for enhanced biodegradability and osseointegration

Composites of poly(L-lactide-trimethylene carbonate-glycolide) and surface modified calcium carbonate whiskers as a potential bone substitute material

On the enhancement of thermo-mechanical properties of poly(L-lactide) by solid-state extrusion for biodegradable spinal fixation devices