Abstract:This study investigates the metallurgical and mechanical properties of a nickel-based superalloy produced through wire + arc additive manufacturing (WAAM). It is a novel and fast fabrication technique based on layer-by-layer construction for rapid product development. A thin-wall component of Inconel 625 was successfully manufactured using a cold metal transfer (CMT)-based WAAM technique with an ErNiCrMo-3 wire after identifying suitable process parameters based on trial runs. The microstructure varies based on the travel and build directions, resulting in columnar, cellular, and equiaxed dendrites found in bottom, middle, and top regions. These dendritic structures evolve throughout the deposition process, predominantly influenced by temperature circumstances. The results of SEM/EDS analysis indicated that Nb and Mo segregation was lower in the interdendritic areas compared to the dendritic core areas of the thin-wall part. The XRD results discovered that the main crystal structure found in the WAAMed samples was a γ-FCC (face-centered cubic). Additionally, through EBSD analysis, the average grain size was identified as 86.45 μm in the travel direction and 89.15 μm in the build direction. The grain properties of the material were influenced by the reheating phenomenon and the circumstances of solidification that occurred throughout the layer-by-layer additive manufacturing process. The larger proportion of higher angle grain boundaries improves the mechanical properties. The average hardness in the travel direction was higher in the top (312 HV), middle (297 HV), and bottom (303 HV) sections than in the build direction (305 HV), (290 HV) and (294 HV), respectively. The mechanical properties, specifically tensile strength, exhibit anisotropy that varies depending on the direction of travel and build. The residual stress analysis shows that the as-built specimen is mainly affected by tensile stress in the travel and build directions.

Investigations and Optimization of Cold Metal Transfer-based WAAM Process Parameters for Fabrication of Inconel 718 Samples using Response Surface Methodology

Optimization of process parameters of cold metal transfer welding-based wire arc additive manufacturing of super Duplex stainless steel using response surface methodology

Impact of Process Parameters on Forming Quality and Deposition Efficiency of Unsupported Rods in Wire Arc Additive Manufacturing

Investigations and Multi-response Optimization of Wire Arc Additive Manufacturing Cold Metal Transfer Process Parameters for Fabrication of SS308L Samples

Investigations and Multi-response Optimization of Process Parameters for SS316L Cold Metal Transfer-Wire Arc Additive Manufactured Samples

The Effects of Processing Parameters during the Wire Arc Additive Manufacturing of 308L Stainless Steel on the Formation of a Thin-Walled Structure

Some studies on optimization of process parameters for wire ARC additive manufacturing of Hastelloy C276 using GRA-GWO hybrid techniques

A Study on Microstructure and Mechanical Properties of Inconel 718 Superalloy Fabricated by Novel CMT-WAAM Process

Effect of welding parameters on bead characteristics and mechanical properties of wire and arc additive manufactured inconel 718

Investigation of Surface Residual Stress, Mechanical Properties, and Metallurgical Characterization of Inconel 625 Multilayer Thin-Wall Component Using Cold Metal Transfer Technique

Multi-Response Optimisation of Wire-Arc Additive Manufacturing Process Parameters for AISI 4130 Steel during remanufacturing process

Influence of pulsed current GTAW-WAAM process parameters on the single layer bead geometry and multi bead multi-layer deposition of a nickel-based superalloy

Technology Development for Producing Inconel 625 in Aerospace Application Using Wire Arc Additive Manufacturing Process

Wire Arc Additive Manufacturing: A Comprehensive Review and Research Directions

Selection of Parameters for Optimized WAAM Structures for Civil Engineering Applications

Influence of droplet transfer behaviour on the microstructure, mechanical properties and corrosion resistance of wire arc additively manufactured Inconel (IN) 625 components

Multi response optimization of Inconel 625 wire arc deposition for development of additive manufactured components using Grey relational analysis (GRA)

Experimental Study And Optimization Of Submerged Arc Welding Parameters For Aisi 1055 Steel Using Response Surface Methodology

Study on the Effect of Powder-Bed Fusion Process Parameters on the Quality of as-Built IN718 Parts Using Response Surface Methodology

Wire Arc Additive Manufacturing of ER-4043 Aluminum Alloy: Effect of Tool Speed on Microstructure, Mechanical Properties and Parameter Optimization

A review on microstructure and mechanical properties of Inconel 625 alloy fabricated using wire arc additive manufacturing process