Abstract:The thermal conversion of waste plastic products can provide a promising solution to the issues of environmental pollution, waste management, and energy needs. However, our present understanding on the thermal reforming of different kinds of plastic wastes mixtures during their co-pyrolysis and co-gasification for syngas production and energy recovery is insufficient. Non-selective urban polypropylene (PP) and polystyrene (PS) waste plastics were chosen for the investigations reported here. Thermal degradation properties of PP and PS as well as their blends in different mass ratios were investigated via thermogravimetric (TG) analysis. Co-pyrolysis and CO 2 -assisted co-gasification of PP-PS blends were then conducted using a fixed-bed reactor at a temperature of 1173 K. Experimental results from the blends were then compared with the weighted value calculated from their component feedstocks to quantify the degree of synergistic effect. TG results showed that the co-treatment of PP and PS enhanced the respective devolatilization process. The co-pyrolysis of PP and PS enhanced their thermal cracking, leading to synergistic increases in the yields of H 2 , light hydrocarbons (HC) and total syngas. In co-gasification, the reforming reaction involving CO 2 was synergistically enhanced, resulting in the increased yields of H 2 and HC. The gasification reactivity of carbon black improved during the co-processing of PP and PS due to the synergistic effect between the two different kinds of plastics. Higher synergistic effects were observed from the plastic mixtures having higher PS content that resulted in increased yield of syngas. Co-gasification of PP-PS blends having 40% PP content (2P3S) exhibited the maximum synergistic effect on H 2 , CO, and total syngas showing increased yields by 88.8%, 77.7%, and 74.2% respectively. The lowest synergistic effect was observed for HC that showed increased yield of only 25.1%. The optimal CO 2 consumption was also observed from the co-gasification of 2P3S. Each gram of 2P3S feedstock consumed approximately 1.80 g of CO 2 to result in highest recovered energy of 27.49 kJ/g and the maximum overall energy efficiency of 43.2%. The results revealed that enhanced thermal cracking and CO 2 reforming reaction, along with the improved reactivity of carbon black were mainly responsible for increased yields of H 2 , HC, CO and total syngas during co-gasification. This study contributes to the fundamental understanding of co-processing of non-separated waste plastics for enhanced syngas production and energy recovery, elucidating the synergistic effect between the various kinds of plastics during their co-pyrolysis and co-gasification.

Co-pyrolysis performances of lignite and waste plastic from the perspective of hydrogen migration and redistribution characteristics

Insight into hydrogen migration and redistribution characteristics during co-pyrolysis of coal and polystyrene

Investigation on Hydrogen Migration and Redistribution Characteristics During Co-Pyrolysis of Lignite with Hydrogen-Rich Carbonaceous Matters

Co-pyrolysis of Lignite and Vacuum Residue: Product Distribution and Hydrogen Transfer

Synergistic effect of Hami coal and polystyrene on products properties during co-pyrolysis: Evaluation on the contribution of different interaction sources

Hydrogen Transfer Route and Interaction Mechanism During Co-Pyrolysis of Xilinhot Lignite and Rice Husk

Co-pyrolysis of pinewood and HDPE: pyrolysis characteristics and kinetic behaviors study

Co-pyrolysis characteristics and synergistic mechanism of low-rank coal and direct liquefaction residue

Co-pyrolysis of Stevia rebaudiana straw and polystyrene: a study on biochars production and characterization

Co-pyrolysis behaviors of low-rank coal and polystyrene with in-situ pyrolysis time-of-flight mass spectrometry

Co-pyrolysis of Sewage Sludge with Hydrogen-Rich Polythene: Effects on Synergistic Promotion and Bio-Oil Quality

Synergistic effects during co-pyrolysis and co-gasification of polypropylene and polystyrene

Investigation on Synergistic Effects and Char Morphology During Co-pyrolysis of Poly(vinyl Chloride) Blended with Different Rank Coals from Northern China

Comparative Study on Synergistic Effects in Co-Pyrolysis of Tobacco Stalk with Polymer Wastes: Thermal Behavior, Gas Formation, and Kinetics

Synergistic Effects on Char and Oil Produced by the Co-Pyrolysis of Pine Wood, Polyethylene and Polyvinyl Chloride

Comparative Study on the Synergistic Co-Pyrolysis of Plastics and Rubber Waste: Thermal Behavior and Product Distributions

Co-pyrolysis of Platanus Wood and Bituminous Coal: Product Distributions, Char Pore Analysis and Synergistic Effects

Co-pyrolysis of Oil Sludge with Hydrogen-Rich Plastics in a Vertical Stirring Reactor: Kinetic Analysis, Emissions, and Products

Effects of Direct Coal Liquefaction Residue Additions on Low-Rank Pulverized Coal during Co-Pyrolysis

Enhanced biofuel production by co-pyrolysis of distiller's grains and waste plastics: A quantitative appraisal of kinetic behaviors and product characteristics

Quantifying the Sources of Synergistic Effects in Co-Pyrolysis of Pinewood and Polystyrene