Abstract:In order to solve the problem of complicated electrochemical machining and unpredictable moulding morphology of shaped hot forging model cavities, this paper takes the "T" shaped cavity made of 40CrNiMoV as the research object. Firstly, the electrolyte formulation development test was carried out for 40CrNiMoV material, and the most suitable electrolyte formulation was selected as 8%NaCl + 11%NaNO 3 composite electrolyte through the measurement and analysis of the polarisation characteristic curve. Secondly, a multi-physical field coupling simulation model of electric field, gas–liquid two-phase flow field, temperature field and structural field is established, and based on the COMSOL software, the flow rate, temperature and bubble rate of electrolyte under different process parameters affect the law of anode surface forming accuracy, and the simulation results show that when the inlet pressure is low, the gap electrolyte flow rate of less than 5 m/s is larger, and it is easy to produce the phenomenon of passivation, which will lead to the temperature and bubble cannot be discharged in time, making the forming accuracy lower; in the electrolytic processing of the cavity bubble rate compared to the temperature has a greater impact on the conductivity, accompanied by the voltage increases, more heat and bubbles are generated in the processing gap, making the cavity forming accuracy worse; higher cathode feed rate can effectively improve the taper of the cavity side wall, so the cathode side wall insulation can avoid excessive corrosion of the non-processing surfaces, and the processing accuracy is significantly improved compared to the uninsulated. Therefore, insulating the cathode side wall can avoid excessive corrosion on the non-machining surface and improve the machining accuracy significantly. Finally, validation tests were carried out to obtain the measured values of the non-planar "T" shaped cavity inner wall profile and to compare the theoretical values of the simulation. The results show that the theoretical values of the coupled multi-physical field simulation are close to the measured values and can simulate the actual electrolytic process more accurately, providing a technological reference for the electrolytic machining of complex-shaped cavities.

Simulation study on cathode structure optimization of aluminum alloy thin-walled internal spiral deep hole electrochemical machining

Analysis of flow field for ECM square deep hole with two-section square cone combination cathode

Machining Surface Improvement through Electric- and Flow-Field Adjustments in Flying Electrochemical Milling of AA 2219

Simulation Analysis and Experimental Validation of Cathode Tool in Electrochemical Mill-Grinding of Ti6Al4V

Research on the precision forming cathode design method of electrochemical machining all-metal screw drill stator

Multiphysics Research on Electrochemical Machining of Micro Holes with Internal Features

Electrochemical machining of a rhombus hole with synchronization of pulse current and low-frequency oscillations

Analysis of flow field for electrochemical machining deep spiral hole with gradually changing groove section

Method for controlling the area of the electrolyte outlets in the flow field simulation and experimental verification of electrochemical machining

Improvement of machining quality by using axial supplementary electrolyte in electrochemical cutting with radial electrolyte flushing

Simulation and Experimental Research on Electrochemical Machining of Cross Groove

Experimental Study on the Influence of Tool Electrode Material on Electrochemical Micromachining of 304 Stainless Steel

Analysis of gas-liquid two-phase flow field with six working teeth spiral incremental cathode for deep special-shaped hole in ECM

Improving flatness of machined surface in rotating cathode electrochemical milling

Study on the forming law of ECM of non-planar "T" shaped cavities based on multi-physical field coupling

Improving surface integrity of micro-holes in ECDM using ultrahigh-speed rotary of tool cathode and non-water-based electrolyte

Study on improving the surface roughness of multi-stage internal cone hole by rotating magnetic field assisted electrochemical machining

Research on pitting control technology of titanium alloy cascade trepanning electrochemical machining

Analysis of electrochemical machining of involute internal spline by foamed metal cathode

Study on Improving Electrochemical Machining Performances through Energy Conversion of Electrolyte Fluid

Electrochemical milling of deep-narrow slots with a pulsating electrolyte flow field