Abstract:Obtaining a perovskite light-absorbing layer with good crystallization, low defect concentration, good stability, and well-matched energy levels is critical to obtaining high-efficiency perovskite solar cells (PSCs). Here, a hybrid PSC with a graded band gap is explored using MAPbBr3 (MA = CH3NH3) and MAPbBr0.9I2.1 quantum dots (QDs) as component cells. We have creatively designed a solar cell device with a double-QD structure [indium tin oxide (ITO)/SnO2/perovskite:MAPbBr3 QDs/MAPbBr0.9I2.1 QDs/Spiro-OMeTAD/Au]. A better crystal film of the perovskite absorption layer can be obtained because the MAPbBr3 QDs are doped in an antisolvent, which induces nucleation and growth in the polycrystalline perovskite. In addition, we expect that digestive ripening occurred in the crystallization, and the oleic acid ligands on the surface of the QDs disintegrate during the doping process and transfer to the surface of the perovskite absorption layer finally; it follows that the hydrophobicity and stability of the perovskite film are greatly enhanced. Moreover, a thin film of MAPbBr0.9I2.1 QDs is introduced between the perovskite absorption layer and the hole layer, acting as an energy-level ladder, which leads to well-matched energy levels, an increase in fill factor (FF), and an enhanced hole transport capability. In particular, the mechanism of the crystallization process involving the effect of oleic acid ligands on the interior and surface of the perovskite film is fully discussed here. The final research results from the PSCs show that both high efficiency and long-term stability are achieved successfully by this design strategy.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.0c14191?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.0c14191</a>.Parameters of carrier lifetimes in TRPL, parameters and calculated values in the Owens two-liquid method experiment, and J–V parameters; QD dispersion images; AFM images; perovskite film images; contact-angle test images; EIS spectrum; and boxplot of J–V parameters (<a class="ext-link" href="/doi/suppl/10.1021/acsami.0c14191/suppl_file/am0c14191_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Ionic‐Rich Vermiculite Tailoring Dynamic Bottom‐Up Gradient for High‐Efficiency Perovskite Solar Cells

Suppressing Ion Migration by Synergistic Engineering of Anion and Cation towards High‐Performance Inverted Perovskite Solar Cells and Modules

Engineering the buried interface in perovskite solar cells via lattice-matched electron transport layer

Improved Performance and Stability of Perovskite Solar Modules by Regulating Interfacial Ion Diffusion with Nonionic Cross‐Linked 1D Lead‐Iodide

Ion Compensation of Buried Interface Enables Highly Efficient and Stable Inverted MA‐Free Perovskite Solar Cells

Strain Engineering and Halogen Compensation of Buried Interface in Polycrystalline Halide Perovskites

Molecular Bridge Assisted Bifacial Defect Healing Enables Low Energy Loss for Efficient and Stable Perovskite Solar Cells

2D/3D heterojunction engineering at the buried interface towards high-performance inverted methylammonium-free perovskite solar cells

Constructing an Interfacial Gradient Heterostructure Enables Efficient CsPbI3 Perovskite Solar Cells and Printed Minimodules

Halides‐enhanced buried interfaces for stable and extremely low‐voltage‐deficit perovskite solar cells

Ethyl Thioglycolate Assisted Multifunctional Surface Modulation for Efficient and Stable Inverted Perovskite Solar Cells

Suppressing halide phase segregation in wide-bandgap perovskite film by co-doping strategy for high-performance and stable perovskite solar cells

Polydentate Ligand Reinforced Chelating to Stabilize Buried Interface toward High‐Performance Perovskite Solar Cells

Ionic Liquid Surface Treatment-Induced Crystal Growth of CsPbIBr2 Perovskite for High-Performance Solar Cells

CsPb2Br5 assisted direct crystallization of 3D perovskite phase for highly efficient and stable solar cells

CH 3 NH 3 PbBr 3– x I x Quantum Dots Enhance Bulk Crystallization and Interface Charge Transfer for Efficient and Stable Perovskite Solar Cells

Downward Homogenized Crystallization for Inverted Wide‐Bandgap Mixed‐Halide Perovskite Solar Cells with 21% Efficiency and Suppressed Photo‐Induced Halide Segregation

Bottom‐Up Defect Modification Through Oily‐Allicin Modified Buried Interface Achieving Highly Efficient and Stable Perovskite Solar Cells

Buried Interface Modulation via Preferential Crystallization in All‐Inorganic Perovskite Solar Cells: The Case of Multifunctional Ti3C2Tx

Imidazole-Based Ionic Liquid Engineering for Perovskite Solar Cells with High Efficiency and Excellent Stability

Iodide Management and Oriented Crystallization Modulation for High‐Performance All‐Air Processed Perovskite Solar Cells