Abstract:A dissimilar joint of martensitic grade P92 and Ni-based Inconel 617 (IN617) alloy are employed commonly in advanced ultra-supercritical (AUSC) units to fabricate thick section components such as steam pipes and turbine rotors. This study investigated the weldability of the IN617 alloy and P92 steel dissimilar welds. Ni-based superalloy ERNiCrMo-3 filler was used to attempt the dissimilar joining for conventional V groove and narrow groove design by employing the gas tungsten arc welding (GTAW) process. The weld metal for the capping pass, backing pass, and near the interface showed the columnar and cellular grains while equiaxed grains are observed corresponding to root and filling passes. The energy dispersive spectroscopy and Electron probe micro-analyzer (EMPA) study confirmed the segregation of the Nb and Mo particles in inter-dendritic spaces and resulted in the formation of the Nb-rich NbC and laves phases and Mo-rich phases. The EDS line map and EPMA study of the P92 interface showed a sharp increase in Cr, Mo, and Ni concentration and a steep decrease in Fe concentration as moving from P92 base metal to weld metal. A negligible diffusion from filler weld to IN617 or vice versa across the IN617 interface was detected. The microhardness gradient along the weldments indicated a sharp rise in hardness value near the P92 fusion boundary due to the formation of the unmixed zone of lower hardness and the P92 coarse-grained heat-affected zone of higher hardness. The weld metal hardness results showed a great variation with an average hardness value for V groove and narrow groove welds of 227 and 262 HV, respectively. The mechanical tests were conducted at the ambient temperatures and data obtained for the weldments were compared with the base metals. The room temperature tensile tests showed the failure from the region of the P92 BM or the interface of P92 BM/weld metal, with joint strength of 646 ± 6 MPa and 747 ± 4 MPa in AW conditions for V groove and narrow groove, respectively. The Charpy impact test (CIT) also showed the variation in impact toughness along the weldments, and the ERNiCrMo-3 filler weld was identified as the weakest region of the welded joint in terms of impact toughness for both the groove designs. The residual stress variation along the thickness of the weld plate was measured using the deep hole drilling (DHT) methods, and the results indicated the peak magnitude of the residual stress for the V groove welded joint. The test results indicated that welded joint produced using ERNiCrMo-3 filler was safe for AUSC power plants' boiler applications for both the groove weld while optimum mechanical properties were measured for narrow groove weld.

Deciphering the Indentation Creep Characteristics and the Metallurgical Aspects of the 9Cr1MoVNb(P91) and SS316LN Dissimilar Butt Joint

Unravelling the microstructure – indentation creep resistance relationships for friction stir welded modified 9Cr-1Mo steel and LN-type 316 stainless-steel dissimilar joints

A comparative study of creep crack growth behaviour amongst the dissimilar P91-IN182-SS316LN and similar P91 weld joints

Creep cavities and carbide evolution in interrupted creep conditions along P91 steel of dissimilar weld joint

Type IV Damage Evolution during Creep of 316LN SS-P91 Steel Dissimilar Weld Joint

Low Cycle Fatigue and Creep Fatigue Interaction Behavior of 9Cr-0.5Mo-1.8w-v-nb Heat-Resistant Steel at High Temperature

Nano-Indentation Creep Behavior of the Vacuum Electron Beam Weldment of 12cr10co3w2monivnbnb Heat Resistant Steel

Carbon diffusion in dissimilar joints between P91 and 12Cr1MoV steels welded by different consumables at high temperature

Characterization of the Cyclic Softening and Remaining Creep Behaviour of P92 Steel Weldment

Creep Rupture Properties of Dissimilar Metal Weld Between Inconel 617B and Modified 9%cr Martensitic Steel

Dissimilar weldments of ferritic/martensitic grade P92 steel and Inconel 617 alloy: Role of groove geometry on mechanical properties and residual stresses

Research on the creep damage and interfacial failure of dissimilar metal welded joint between 10Cr9Mol VNbN and 12CrlMoV steel

Residual stress analysis, microstructural characterization, and mechanical properties of tungsten inert gas-welded P92/AISI 304L dissimilar steel joints

Creep Behavior and Microstructure Evaluation of Welded Joint in Dissimilar Modified 9cr–1mo Steels

Creep behavior and in-depth microstructural characterization of dissimilar joints

Nanoindentation and indentation creep analysis of diffusion bonded of inconel 718 and AISI 304L stainless steel joint interface

Effect of Groove Design and Post-Weld Heat Treatment on Microstructure and Mechanical Properties of P91 Steel Weld

Study on Creep Rupture Properties of Inconel 617B and 10%cr Steel Dissimilar Metal Weld

Creep rupture study of dissimilar welded joints of P92 and 304L steels

Research on the creep damage and interfacial failure of dissimilar metal welded joint between 10Cr9Mo1VNbN and 12Cr1MoV steel

Influence of Preheating and Post Heating on Diffusible Hydrogen Content, Residual Stresses and Hydrogen Assisted Cracking (HAC) Susceptibility of Induction Assisted Gas Metal Arc Welded P91 Steel Joint