Abstract:Abstract Renewed interest in wave impact assessment has risen for various reasons: • The low airgap of some existing Mobile Units in the North Sea • The COSL Innovator incident and related to this topic the new DNV-GL guidelines (OTG 13 and OTG 14). • the installation of many large-diameter monopile foundations for wind turbines in increasingly deep water in the North Sea. • The installation of many large-diameter wind turbines in increasingly deep water in the North Sea. • Seabed subsidence (and maybe water level rises due to global warming) and their effect on the decreasing airgap of fixed platforms. Wave impact assessment has been the subject of many recent studies and research projects, and there has been a strong knowledge and tool development during the last decade, both within model testing and numerical (CFD) analysis (Huang et.al (2017), de Ridder et.al, (2017), Vestbøstad et. al. (2017), Bunnik et.al. (2018)). However, there is still a lack of efficient methods and tools to properly analyze wave impacts and derive the statistical variation of these impacts in the sea states to which these structures are exposed during their lifetime. To reduce the statistical uncertainties that are naturally arising in estimates of design loads related to extreme waves, sufficient data must be gathered. In order to estimate the design loads it is common practice not to investigate all possible sea states (i.e. long-term analysis) but to investigate a few sea states and assume that the design value occurs at a prescribed probability level in the sea states with the same probability level (i.e. contour line approach). The estimate of the design value at that probability level is then based on results from a limited number of random realizations of these sea states. For linear or weakly nonlinear response types it is possible to estimate design loads accurately with a quite limited number of realizations. For strongly nonlinear problems however this is not possible due to the large statistical variation in the maximum observations, inherent to a random nonlinear process. Estimating accurately the tail of the load distribution requires many more realizations. This approach is restricted by time and costs and eventually one may have to accept an estimated design load with a large statistical uncertainty and account for the uncertainty with a higher safety margin. In this paper an improved methodology for estimating design loads related to extreme wave impacts will be presented. The methodology is based on screening many 3-hour realizations of the design sea states with simplified, fast but sufficiently accurate methods and to focus only on the potentially critical events with a model containing a more complete description of the physics. This can be either a model test or a non-linear impact simulation (i.e. CFD analysis). By doing this many more rare/critical events can be assessed, reducing the statistical uncertainty in the estimate of the design load. A screening method/wave impact indicator will be presented for a jacket platform and for a fixed offshore wind turbine. Existing model test data is used to show the correlation between indicator and actual impact events and to derive the efficiency of the impact indicators.

Methodology for weather window analysis of weather-restricted marine operations using response-based load-resistance factors

An ULS reliability-based design method for mooring lines using an efficient full long-term approach

Methodology for Assessment of the Allowable Sea States During Installation of an Offshore Wind Turbine Transition Piece Structure Onto a Monopile Foundation

Influence of Wind Shear Uncertainty in Long-Term Extreme Responses of an Offshore Monopile Wind Turbine

Integrated Numerical Investigation of a 15 MW Semi-Submersible Wind Turbine at Moderate Water Depth

OC6 Phase I: Investigating the Underprediction of Low-Frequency Hydrodynamic Loads and Responses of a Floating Wind Turbine

Dynamic Behavior of Piled Jacket Offshore Wind Turbines Based on Integrated Aero-Servo-hydro-ssi-owt Model

Laboratory investigation on short design wave extreme responses for floating hinged-raft wave energy converters

Response Extremes of Floating Offshore Wind Turbine Based on Inverse Reliability and Environmental Contour Method

Comparison of environmental contour and response-based approaches for system reliability analysis of floating structures

Sensitivity analysis of numerical modeling input parameters on floating offshore wind turbine loads

Dynamic response of a shallow-draft floating wind turbine concept: Experiments and modelling

Numerical Prototyping of Floating Offshore Wind Turbines: Virtual Operation in Real Environmental Conditions

System reliability analysis of mooring system for floating offshore wind turbine based on environmental contour approach

Multi‐hazard fragility assessment of monopile offshore wind turbines under earthquake, wind and wave loads

Efficient Indicators for Screening of Random Waves for Wave Impacts on a Jacket Platform and a Fixed Offshore Wind Turbine

Mooring system fatigue analysis of a floating offshore wind turbine

Dynamic Behavior of a 10 MW Floating Wind Turbine Concrete Platform under Harsh Conditions

Fluctuating wind and wave simulations and its application in structural analysis of a semi-submersible offshore platform

Long-Term Extreme Load Prediction of Spar and Semisubmersible Floating Wind Turbines Using the Environmental Contour Method

Cross-comparison analysis of environmental load components in extreme conditions for pontoon-connected semi-submersible FOWT using CFD and potential-based tools