Abstract:The acidic (pKa ≈1.5–2.5) and hygroscopic nature of poly(3,4-ethylene dioxythiophene) polystyrene sulfonate, used as a common hole-injection layer in optoelectronic devices, has a detrimental effect on device stability and is associated with well established device failure mechanisms. In this work, a process with a high green index hole-injection layer material (V2O5) and low surface roughness (RMS roughness ≈1.3 nm) was developed for demonstrating a hybrid polymer–inorganic perovskite light-emitting diode. Test devices with the new hole-injection layer demonstrate nearly identical maximum current efficiencies (4.23 vs 4.19 cd/A), and luminous efficacies (2.99 vs 2.32 lm/W) when compared to a control device fabricated with the conventional hole-injection layer. Furthermore, the peak brightness was achieved at a current density one-third of the value for the control device. To examine the transport of holes in the above hole-injection layer, we carried out device simulations based on a physical charge control model, including defect-assisted tunneling for hole injection. Close agreement for current–voltage characteristics is observed. Experimentally measured mobility in the device and measured radiative lifetimes were found to be sufficient to achieve this agreement without resorting to the introduction of a sheet charge at the injection interface. Despite the use of a bulk-heterojunction device architecture, the model predicts high radiative recombination rates [≈5.6×1022/(cm3s)] in the emissive layer, consistent with the measured photophysical properties for the active film, suggesting effective passivation of non-radiative surface states.

Improved hole injection for CsPbI 3 nanocrystals based light-emitting diodes via coevaporation of hole transport layer

Improvement of Blue Llight-Ight-ight-eeemitting Mitting Ddiodes Iodes with an Undoped Graded Layer As the Electrons Tunneling Barrier Layer

Improved Performance of Hybrid Organic/Inorganic P–n Heterojunction White Light‐Emitting Diodes with 4,4′‐cyclohexane‐1,1‐diylbis[ N , N ‐bis(4‐methylphenyl)aniline] As a Multifunctional Hole Transport Layer

Polymeric Hole Transport Materials for Red CsPbI3 Perovskite Quantum-Dot Light-Emitting Diodes

Defect-assisted hole transport through transition metal oxide-based injection layers for passivated nanocrystalline CsPbBr3 emissive thin films: A combined experimental and modeling study

Promoted Hole Transport Capability by Improving Lateral Current Spreading for High‐Efficiency Quantum Dot Light‐Emitting Diodes

Bidirectional Inhibiting Interfacial Ion Migration in the Inorganic Hole Transport Layer for Perovskite Light-Emitting Diodes

Improving the Performance of Quantum Dot Light-Emitting Diodes by the Enrichment of a Fluorinated Component on Top of a Hole Transport Layer

Single Conjugated Polymer with Four Stepwise HOMO Levels for Effective Hole Injection Across Large Barrier 1.4 Ev to Core–Shell Quantum Dot Layer for Electroluminescence in Inverted QLED

Using Thermally Crosslinkable Hole Transporting Layer to Improve Interface Characteristics for Perovskite CsPbBr3 Quantum-Dot Light-Emitting Diodes

Solution-Processed Efficient Perovskite Nanocrystal Light-Emitting Device Utilizing Doped Hole Transport Layer

Surface Treatment of Inorganic CsPbI3 Nanocrystals with Guanidinium Iodide for Efficient Perovskite Light-Emitting Diodes with High Brightness

Perovskite Light-Emitting Devices with Doped Hole Transporting Layer

Multidentate Ligand-Passivated CsPbI3 Perovskite Nanocrystals for Stable and Efficient Red-Light-Emitting Diodes.

An Efficient Hole Transporting Polymer for Quantum Dot Light‐Emitting Diodes

Performance Enhancement of Perovskite Quantum Dot Light-Emitting Diodes via Management of Hole Injection

Improved Current Density of Inverted Perovskite Solar Cells via Hole Transport Layer Doping

Enhancing hole injection by electric dipoles for efficient blue InP QLEDs

High efficiency quantum-dot light-emitting diodes enabled by boosting hole injection

<SUP>C</SUP>u<SUP>2+</SUP>-Doped CsPbI<sub>3</sub> Nanocrystals with Enhanced Stability for Light-Emitting Diodes

The effect of carrier transport layer on the electroluminescent properties of solution‐processed thermally activated delayed fluorescent device based on 4CzPN