Abstract:The system designed in this study involves a three-dimensional (3D) microelectronic mechanical system chip structure using DNA printing technology. We employed diverse diameters and cavity thickness for the heater. DNA beads were placed in this rapid array, and the spray flow rate was assessed. Because DNA cannot be obtained easily, rapidly deploying DNA while estimating the total amount of DNA being sprayed is imperative. DNA printings were collected in a multiplexer driver microelectronic mechanical system head, and microflow estimation was conducted. Flow-3D was used to simulate the internal flow field and flow distribution of the 3D spray room. The simulation was used to calculate the time and pressure required to generate heat bubbles as well as the corresponding mean outlet speed of the fluid. The "outlet speed status" function in Flow-3D was used as a power source for simulating the ejection of fluid by the chip nozzle. The actual chip generation process was measured, and the starting voltage curve was analyzed. Finally, experiments on flow rate were conducted, and the results were discussed. The density of the injection nozzle was 50, the size of the heater was 105 μm × 105 μm, and the size of the injection nozzle hole was 80 μm. The maximum flow rate was limited to approximately 3.5 cc. The maximum flow rate per minute required a power between 3.5 W and 4.5 W. The number of injection nozzles was multiplied by 100. On chips with enlarged injection nozzle density, experiments were conducted under a fixed driving voltage of 25 V. The flow curve obtained from various pulse widths and operating frequencies was observed. The operating frequency was 2 KHz, and the pulse width was 4 μs. At a pulse width of 5 μs and within the power range of 4.3-5.7 W, the monomer was injected at a flow rate of 5.5 cc/min. The results of this study may be applied to estimate the flow rate and the total amount of the ejection liquid of a DNA liquid.

Three-phase contact line confined dense nanoparticle array for high-capacity DNA synthesis

Porous pDMS Microreactor Array Chip for De Novo DNA Synthesis

A Novel DNA Synthesis Platform Design with High-Throughput Paralleled Addressability and High-Density Static Droplet Confinement

A Versatile Microchannel Array Device for Portable and Parallel Droplet Generation

Inkjet printing-based high-throughput DNA synthesis

Design of a DNA Synthesis Chip for Data Storage with Ultra-High Throughput and Density Featuring Large-Scale Integrated Circuits and Microfluidic Confinement

DNA microarray fabricated on poly(acrylic acid) brushes-coated porous silicon by in situ rolling circle amplification.

Binary DNA Arrays on Heterogeneous Patterned Surfaces

Highly Transparent Cyclic Olefin Copolymer Film with a Nanotextured Surface Prepared by One-Step Photografting for High-Density DNA Immobilization.

In situ synthesis of DNA microarray on functionalized cyclic olefin copolymer substrate

Inkjet Printing of a Micro/Nanopatterned Surface to Serve as Microreactor Arrays

Massively Parallel Nanoparticle Synthesis in Anisotropic Nanoreactors.

Bead-Droplet Reactor for High-Fidelity Solid-Phase Enzymatic DNA Synthesis

Resilient Three-Dimensional Ordered Architectures Assembled from Nanoparticles by DNA

Microarray Platforms Based on 3D Printing

DNA-library assembly programmed by on-demand nano-liter droplets from a custom microfluidic chip

Nanoscale Patterns of Oligonucleotides Formed by Electrohydrodynamic Jet Printing with Applications in Biosensing and Nanomaterials Assembly

A 3D Scalable Chamber-Array Chip for Digital LAMP.

DNA Printing Integrated Multiplexer Driver Microelectronic Mechanical System Head (IDMH) and Microfluidic Flow Estimation

A Robotics Platform for Automated Batch Fabrication of High Density, Microfluidics-Based DNA Microarrays, with Applications to Single Cell, Multiplex Assays of Secreted Proteins.

One-Step Fabrication of Droplet Arrays Using a Biomimetic Structural Chip.