Abstract:Properties such as wide bandgap, higher electromechanical coupling, and low dielectric permittivity have propelled ScxAl1−xN as an advantageous material for optoelectronics and RF applications. ScxAl1−xN devices are challenging to fabricate because ScAlN films are complex to etch, especially with greater scandium concentrations. Our group has developed a procedure to etch ScxAl1−xN (x = 0.125, 0.20, 0.40) thin films (~ 730 nm thick), which results in vertical sidewalls that approach 85–90° (± 0.4°) and reduce the degree of the undercut. To maintain uniformity between various Sc compositions during the etching process, a nitrogen atmosphere was employed for high-temperature annealing, followed by immersion in a bath of tetramethyl ammonium hydroxide (TMAH) for wet etching. A 25% concentrated TMAH solution was used at 78–82 °C to etch down the ScxAl1−xN film layer. The etching rate of Sc0.125Al0.875N$${\mathrm{Sc}}_{0.125}{\mathrm{Al}}_{0.875}\mathrm{N}$$, Sc0.20Al0.80N$${\mathrm{Sc}}_{0.20}{\mathrm{Al}}_{0.80}\mathrm{N}$$, and Sc0.40Al0.60N$${\mathrm{Sc}}_{0.40}{\mathrm{Al}}_{0.60}\mathrm{N}$$ was found to be approximately, 365 nm/min, 243 nm/min, and 81 nm/min, respectively. Experimental results demonstrated that an identical etching profile can be obtained by TMAH vapor as well. We demonstrated how the annealing process recovers the deterioration introduced into the ScxAl1−xN by the ion-bombardment effect developed during the SiO2/SiNx hard mask dry etch step, ultimately preventing lateral etching. We have also reduced sidewall roughness of a post-etched ScxAl1−xN film with the combination of inductively coupled plasma etch, high-temperature annealing, and wet etching without affecting the sidewall verticality. Preliminary results of ongoing device fabrication that use this developed etch approach are also presented herewith to give an overview of the ongoing work.Graphical abstractOur group has developed a state-of-the-art procedure to etch ScxAl1−xN (x = 0.125, 0.20, 0.40) thin films (~ 730 nm thick), which results in vertical sidewalls that approach 85–90° (± 0.4°) and reduce the degree of the undercut. To maintain uniformity between various Sc compositions during the etching process, a nitrogen atmosphere was employed for high-temperature annealing, followed by immersion in a bath of tetramethyl ammonium hydroxide (TMAH) for wet etching. A 25% concentrated TMAH solution was used at 78–82 °C to etch down the ScxAl1−xN film layer. Experimental results demonstrated that an identical etching profile can be obtained by TMAH vapor as well. We demonstrated how the annealing process recovers the deterioration introduced into the ScxAl1−xN by the ion-bombardment effect developed during the SiO2/SiNx hard mask dry etch step, ultimately preventing lateral etching. We have also reduced sidewall roughness of a post-etched ScxAl1−xN film with the combination of inductively coupled plasma (ICP) etch, high-temperature annealing, and wet etching without affecting the sidewall verticality.

A Segmented‐Target Sputtering Process for Growth of Sub‐50 nm Ferroelectric Scandium–Aluminum–Nitride Films with Composition and Stress Tuning

Deposition of highly crystalline AlScN thin films using synchronized high-power impulse magnetron sputtering: From combinatorial screening to piezoelectric devices

Nanoscale Structural and Chemical Properties of Ferroelectric Aluminum Scandium Nitride Thin Films

A study of sputtering process for nanocrystalline FeAlN soft magnetic thin films

Deposition of highly-crystalline AlScN thin films using synchronized HiPIMS -- from combinatorial screening to piezoelectric devices

Etching of scandium-doped aluminum nitride using inductively coupled plasma dry etch and tetramethyl ammonium hydroxide

Epitaxial Growth of Sc0.09Al0.91N and Sc0.18Al0.82N Thin Films on Sapphire Substrates by Magnetron Sputtering for Surface Acoustic Waves Applications

Investigation of Optimum Deposition Conditions of Radio Frequency Reactive Magnetron Sputtering of Al0.7Sc0.3N Film with Thickness down to 20 nm

Low temperature sputtering deposition of Al1−xScxN thin films: Physical, chemical, and piezoelectric properties evolution by tuning the nitrogen flux in (Ar + N2) reactive atmosphere

Al1−xScxN Thin Films at High Temperatures: Sc-Dependent Instability and Anomalous Thermal Expansion

Fabrication of Ultrathin Ferroelectric Al0.7Sc0.3N Films under Complementary‐Metal‐Oxide‐Semiconductor Compatible Conditions by using HfN0.4 Electrode

Deposition, Characterization, and Modeling of Scandium-Doped Aluminum Nitride Thin Film for Piezoelectric Devices

Ultrathin AlScN for low-voltage driven ferroelectric-based devices

Effects of High-Temperature Thermal Annealing on the Crystal Structure and Phase Separation in Sputtered ScAlN Thin Films

Metal‐Organic Chemical Vapor Deposition of Aluminum Scandium Nitride

High Quality Co-Sputtering AlScN Thin Films for Piezoelectric Lamb-Wave Resonators

Method of controlling coupling coefficient of Aluminum Scandium Nitride deposition in high volume production

Demonstration and STEM Analysis of Ferroelectric Switching in MOCVD-Grown Single Crystalline Al$_{0.85}$Sc$_{0.15}$N

Piezoelectric and elastic properties of Al0.60Sc0.40N thin films deposited on patterned metal electrodes

Improving Reproducibility of Sputter Deposited Ferroelectric Wurtzite Al0.6Sc0.4N Films using In-situ Optical Emission Spectrometry

Vertical and Lateral Etch Survey of Ferroelectric AlN/Al1-xScxN in Aqueous KOH Solutions