Abstract:Cement is the most important binding agent used in soil stabilization and significantly improves the strength and compressibility of soils. However, owing to the significant environmental and socio-economic impact of cement production, alternative, low-carbon binders are increasingly being sought. Among them, waste-based inorganic additives used in construction provide sustainable soil treatment materials and reduce the need for landfills. Effective mud stabilization depends on the type of stabilizers and their mineralogical setup, as well as an understanding of their water absorption capacity. Therefore, this study investigated the factors influencing the water absorption characteristics of waste-based additives, including paper sludge ash (PSA), palm kernel shell ash (PKSA), rice husk ash (RHA), coal fly ash, hemihydrate gypsum, limestone powder, and basalt rock powder (BRP). The water absorption capacity ( W ab ) of each additive represents the amount of water absorbed per gram evaluated via the suction filtration method. The long-term water absorption capacities of the waste additives were compared with a conventional additive, blast furnace cement class B (BFCB). Although PSA, PKSA, and RHA absorbed more water than BFCB under short-term curing, BFCB exhibited the highest W ab under long-term curing. PSA, PKSA, and RHA had a water absorption capacity at 4 h ( W ab ) t = 4h of 74.5%, 107.3%, and 62.9%, respectively, whereas that of BFCB was 37.4%. In contrast, after 168 h, the water absorption capacity of BFCB increased to 126.1%. These evaluated water absorption capacities were categorized into immediate and time-dependent stages. Mercury intrusion porosimetry, X-ray diffraction (XRD), and scanning electron microscopy investigations were conducted to investigate the influence of factors such as porosity and hydration of the different additives on water absorption capacity. The results showed that porosity characteristics affect the immediate water absorption capacity, and hydrate formation contributes to increased water absorption during curing. The waste additives PSA, PKSA, and RHA with irregular surfaces and pores were highly porous and exhibited a high immediate water absorption capacity ( W ab ) t = 4h , unlike the additives with flat surfaces and less irregularities with lower ( W ab ) t = 4h . The XRD investigation revealed that the presence of ettringite and calcite contributed to increased water absorption during curing for PSA, PKSA, and BFCB. The generation of needle-like ettringite could promote a denser microstructure in PSA, PKSA, and BFCB, thus further improving W ab during curing. Finally, using cone index strength, we explored the effective application of waste-based additives as soil stabilizers, attempting to predict the effect of water absorption capacity on the properties of treated soil. The stabilizer addition ratio ( A ) and W ab of the waste additives were found to be essential indicators for predicting the strength development of treated clays. A clear correlation was observed between the cone index ( q c ) and parameter β ( t ), which is derived from W ab and A , of the treated clays.

Assessing the stabilization impact of silica fume and phosphogypsum on hydro-mechanical characteristics of clayey sand

Strength performance and enhancement mechanism of silty sands stabilized with cement, red mud, and phosphogypsum

Experimental Study on Mechanical Properties of Soft Clay Stabilized by Industrial By-Products

The stabilisation of clayey soil by using sawdust and sawdust ash

Performance and mechanism of sand stabilization via microbial-induced CaCO3 precipitation using phosphogypsum

Stabilization of a Clay Soil Using Cementing Material from Spent Refractories and Ground-Granulated Blast Furnace Slag

Application of phosphogypsum in soil stabilization

Stabilization of Fluidic Silty Sands with Cement and Steel Slag

Strength Performance of Soft Clayey soil Solidified by Slag- Fly Ash – Metakaolin Based Geopolymer

Stabilization of Highly Decomposed Peat Soil: Mechanical, Physicochemical, and Microscopic Examination

Combined Influences of Cement, Rice Husk Ash and Fibre on the Mechanical Characteristics of a Calcareous Sand

Analysis of the Mechanical Properties of Cured Sludge by Alkaline Excitation of Phosphogypsum

Performance Evaluation and Microstructural Assessment of Industrial Solid Waste as Sustainable Additives for Expansive Soil

Performances of Using Geopolymers Made with Various Stabilizers for Deep Mixing

Influence of polyurethane in the polymerization process for poorly graded sand stabilization and cementing

Comparative Study between Silica Fume and Nano Silica Fume in Improving the Shear Strength and Collapsibility of Highly Gypseous Soil

Evaluation of the long-term performance of stabilized sandy soil using binary mixtures: A micro- and macro-level approach

Pore fluid salinity effects on post-stabilization performance of cement-treated Marl

Evaluation on the Mechanical Properties of Ground Granulated Blast Slag (GGBS) and Fly Ash Stabilized Soil via Geopolymer Process

The effects of desulfurized gypsum on the mechanical properties of dredged clay with high initial water content stabilized by ternary geopolymer

Insights into water absorption characteristics of various waste-based inorganic additives and their application for soil stabilization