Abstract:The main purpose of this research is to bolster mechanical properties of the parts, produced by an extrusion-based 3D printer, or fused deposition modeling machine, via increasing the content of continuous fiber yarn to its practical limit. In-melt continuous glass fiber yarn embedding was applied as a reliable and consistent method for simultaneous impregnation to produce continuous fiber-reinforced thermoplastic composites in the fused deposition modeling process. It is well known that the main weakness in the fused deposition modeling 3D printed products is their low strength compared to the manufactured ones by conventional methods such as injection molding and machining processes. This characteristic can be related to both inherent weakness of thermoplastic materials and poor adhesion between the deposited rasters and the layers. Although various attempts have been performed to tackle this issue, it is widely believed that using continuous fibers is the most effective method to serve this purpose if a reliable and consistent method is implemented. Since the mechanical properties of continuous fiber-reinforced composites directly depend on the content of fiber volume, maximizing the fiber content as well as producing an integrated part was assumed as the main objective. In this work, an analysis of various patterns of raster deposition was conducted, followed by the experiments and verification. The effective parameters on the fiber yarn volume, such as fiber yarn diameter, fiber yarn laying pattern, extrusion width, layer height, and flow percentage, were investigated and their optimal values were reported. The attained experimental results showed that, for polylactic acid-glass fiber yarn reinforced composite, with the extrusion width of 0.3 mm, the layer heights of 0.22 mm, flow percentage of 0.43, and the rectangular laying pattern, approximately 50% fiber-volume content can be achieved which resulted in tensile yield strength and modulus of 478 MPa and 29.4 GPa, respectively. There was an excellent agreement between these experimental results and predicted theoretically values by rule of mixture.

Fiber–matrix impregnation behavior during additive manufacturing of continuous carbon fiber reinforced polylactic acid composites

Fabrication and Formability of Continuous Carbon Fiber Reinforced Resin Matrix Composites Using Additive Manufacturing

An investigation of preparation of continuous carbon fiber reinforced PLA prepreg filament

Impregnation modeling and preparation optimization of continuous glass fiber reinforced polylactic acid filament for 3D printing

Process-dependent Multiscale Modeling for 3D Printing of Continuous Fiber-reinforced Composites

The fabrication of long carbon fiber reinforced polylactic acid composites via fused deposition modelling: Experimental analysis and machine learning

An innovative design approach in three-dimensional printing of continuous fiber–reinforced thermoplastic composites via fused deposition modeling process: In-melt simultaneous impregnation

Experimental and Theoretical Studies on 3D Printed Short and Continuous Carbon Fiber Hybrid Reinforced Composites

The Micro–Macro Interlaminar Properties of Continuous Carbon Fiber-Reinforced Polyphenylene Sulfide Laminates Made by Thermocompression to Simulate the Consolidation Process in FDM

Evolution of microstructure and thermo‐mechanical attributes of fiber reinforced polyamide during fused deposition modeling 3D printing: A comprehensive characterization study

Improving mechanical properties of continuous fiber-reinforced thermoplastic composites produced by FDM 3D printer

An investigation into mechanical properties of a 3D printed two-matrix continuous fiber composites with multi-cavity structure

Additive manufacturing of carbon fiber-reinforced plastic composites using fused deposition modeling: Effects of process parameters on tensile properties

The technology of continuous fibre-reinforced polymers: a review on extrusion additive manufacturing methods

A Continuous Fiber-Reinforced Additive Manufacturing Processing Based on PET Fiber and PLA

Additive Manufacturing of Continuous Fiber-Reinforced Polymer Composites via Fused Deposition Modelling: A Comprehensive Review

High-Throughput Additive Manufacturing of Continuous Carbon Fiber-Reinforced Plastic by Multifilament

3D printing for continuous fiber reinforced thermoplastic composites: mechanism and performance

3D Printing Technology for Short-continuous Carbon Fiber Synchronous Reinforced Thermoplastic Composites: A Comparison between Towpreg Extrusion and In Situ Impregnation Processes

Design and fabrication of high-performance 3D printed continuous flax fibre/PLA composites

Process parameters and mechanical properties of continuous glass fiber reinforced composites-polylactic acid by fused deposition modeling