Abstract:Deploying a dense network of sensors around emitting industrial facilities allows to detect and quantify possible CH4 leaks and monitor the emissions continuously. Designing such a monitoring network with highly precise instruments is limited by the elevated cost of instruments, requirements of power consumption and maintenance. Low cost and low power metal oxide sensor could come handy to be an alternative to deploy this kind of network at a fraction of the cost with satisfactory quality of measurements for such applications.Recent studies have tested Metal Oxide Sensors (MOx) on natural and controlled conditions to measure atmospheric methane concentrations and showed a fair agreement with high precision instruments, such as those from Cavity Ring Down Spectrometers (CRDS). Such results open perspectives regarding the potential of MOx to be employed as an alternative to measure and quantify CH4 emissions on industrial facilities. However, such sensors are known to drift with time, to be highly sensitive to water vapor mole fraction, have a poor selectivity with several known cross-sensitivities to other species and present significant sensitivity environmental factors like temperature and pressure. Different approaches for the derivation of CH4 mole fractions from the MOx signal and ancillary parameter measurements have been employed to overcome these problems, from traditional approaches like linear or multilinear regressions to machine learning (ANN, SVM or Random Forest).Most studies were focused on the derivation of ambient CH4 concentrations under different conditions, but few tests assessed the performance of these sensors to capture CH4 variations at high frequency, with peaks of elevated concentrations, which corresponds well with the signal observed from point sources in industrial sites presenting leakage and isolated methane emission. We conducted a continuous controlled experiment over four months (from November 2019 to February 2020) in which three types of MOx Sensors from Figaro® measured high frequency CH4 peaks with concentrations varying between atmospheric background levels up to 24 ppm at LSCE, Saclay, France. We develop a calibration strategy including a two-step baseline correction and compared different approaches to reconstruct CH4 spikes such as linear, multilinear and polynomial regression, and ANN and random forest algorithms. We found that baseline correction in the pre-processing stage improved the reconstruction of CH4 concentrations in the spikes. The random forest models performed better than other methods achieving a mean RMSE = 0.25 ppm when reconstructing peaks amplitude over windows of 4 days. In addition, we conducted tests to determine the minimum amount of data required to train successful models for predicting CH4 spikes, and the needed frequency of re-calibration / re-training under these controlled circumstances. We concluded that for a target RMSE <= 0.3 ppm at a measurement frequency of 5s, 4 days of training are required, and a recalibration / re-training is recommended every 30 days.Our study presents a new approach to process and reconstruct observations from low cost CH4 sensors and highlights its potential to quantify high concentration releases in industrial facilities.

Self‐Made Equipment for Automatic Methane Diffusion and Ebullition Measurements From Aquatic Environments

Measuring Dissolved Methane in Aquatic Ecosystems Using An Optical Spectroscopy Gas Analyzer

Sensitive Drone Mapping of Methane Emissions without the Need for Supplementary Ground-Based Measurements

Rapid quantification of methane in water with parts-per-billion sensitivity using a metal-organic framework-functionalized quartz crystal resonator

Field evaluation of an autonomous, low-power eddy covariance CO2 flux system for the marine environment

Exploring the temporal dynamics of methane ebullition in a subtropical freshwater reservoir

Dynamic chamber as a more reliable technique for measuring methane emissions from aquatic ecosystems

Addressing Low-Cost Methane Sensor Calibration Shortcomings with Machine Learning

Emission Determination by Three Remote Sensing Methods in Two Release Trials

A Wavelength Modulation Spectroscopy-Based Methane Flux Sensor for Quantification of Venting Sources at Oil and Gas Sites

Reconstruction of High-Frequency Methane Atmospheric Concentration Peaks from Measurements Using Metal Oxide Low-Cost Sensors

Design and evaluation of a low-cost sensor node for near-background methane measurement

Using metal oxide gas sensors for the estimate of methane controlled releases: reconstruction of the methane mole fraction time-series and quantification of the release rates and locations

Electronic Nose for Improved Environmental Methane Monitoring

The Potential of Low-Cost Tin-Oxide Sensors Combined with Machine Learning for Estimating Atmospheric CH4 Variations Around Background Concentration

Deep-Sea Sediment and Water Simulator for Investigation of Methane Seeping and Hydrate Formation

A Novel, Compact Optical Device for Estimating the Methane Emissions in Geological Environment

Using metal oxide gas sensors to estimate the emission rates and locations of methane leaks in an industrial site: assessment with controlled methane releases

Validation and field application of a low-cost device to measure CO2 and evapotranspiration (ET) fluxes

Long-term continuous monitoring of methane emissions at an oil and gas facility using a multi-open-path laser dispersion spectrometer

A measurement system for CO2 and CH4 emissions quantification of industrial sites using a new in situ concentration sensor operated on board uncrewed aircraft vehicles