Abstract:Deploying a dense network of sensors around emitting industrial facilities allows to detect and quantify possible CH4 leaks and monitor the emissions continuously. Designing such a monitoring network with highly precise instruments is limited by the elevated cost of instruments, requirements of power consumption and maintenance. Low cost and low power metal oxide sensor could come handy to be an alternative to deploy this kind of network at a fraction of the cost with satisfactory quality of measurements for such applications.Recent studies have tested Metal Oxide Sensors (MOx) on natural and controlled conditions to measure atmospheric methane concentrations and showed a fair agreement with high precision instruments, such as those from Cavity Ring Down Spectrometers (CRDS). Such results open perspectives regarding the potential of MOx to be employed as an alternative to measure and quantify CH4 emissions on industrial facilities. However, such sensors are known to drift with time, to be highly sensitive to water vapor mole fraction, have a poor selectivity with several known cross-sensitivities to other species and present significant sensitivity environmental factors like temperature and pressure. Different approaches for the derivation of CH4 mole fractions from the MOx signal and ancillary parameter measurements have been employed to overcome these problems, from traditional approaches like linear or multilinear regressions to machine learning (ANN, SVM or Random Forest).Most studies were focused on the derivation of ambient CH4 concentrations under different conditions, but few tests assessed the performance of these sensors to capture CH4 variations at high frequency, with peaks of elevated concentrations, which corresponds well with the signal observed from point sources in industrial sites presenting leakage and isolated methane emission. We conducted a continuous controlled experiment over four months (from November 2019 to February 2020) in which three types of MOx Sensors from Figaro® measured high frequency CH4 peaks with concentrations varying between atmospheric background levels up to 24 ppm at LSCE, Saclay, France. We develop a calibration strategy including a two-step baseline correction and compared different approaches to reconstruct CH4 spikes such as linear, multilinear and polynomial regression, and ANN and random forest algorithms. We found that baseline correction in the pre-processing stage improved the reconstruction of CH4 concentrations in the spikes. The random forest models performed better than other methods achieving a mean RMSE = 0.25 ppm when reconstructing peaks amplitude over windows of 4 days. In addition, we conducted tests to determine the minimum amount of data required to train successful models for predicting CH4 spikes, and the needed frequency of re-calibration / re-training under these controlled circumstances. We concluded that for a target RMSE <= 0.3 ppm at a measurement frequency of 5s, 4 days of training are required, and a recalibration / re-training is recommended every 30 days.Our study presents a new approach to process and reconstruct observations from low cost CH4 sensors and highlights its potential to quantify high concentration releases in industrial facilities.

A measurement system for CO2 and CH4 emissions quantification of industrial sites using a new in situ concentration sensor operated on board uncrewed aircraft vehicles

A new aerial approach for quantifying and attributing methane emissions: implementation and validation

Mobile Atmospheric Measurements and Local-Scale Inverse Estimation of the Location and Rates of Brief CH4 and CO2 Releases from Point Sources

Local-scale atmospheric inversions to monitor CH4 emissions from industrial sites using mobile and/or fixed-point measurements

Development of an Integrated Lightweight Multi-Rotor UAV Payload for Atmospheric Carbon Dioxide Mole Fraction Measurements

Assessing Greenhouse Gas Monitoring Capabilities Using SolAtmos End-to-End Simulator: Application to the Uvsq-Sat NG Mission

Development of a low-cost UAV-based system for CH4 monitoring over oil fields

Sensitive Drone Mapping of Methane Emissions without the Need for Supplementary Ground-Based Measurements

Controlled-release Experiment to Investigate Uncertainties in UAV-based Emission Quantification for Methane Point Sources

A Study of a Miniature TDLAS System Onboard Two Unmanned Aircraft to Independently Quantify Methane Emissions from Oil and Gas Production Assets and Other Industrial Emitters

Aircraft-Based AirCore Sampling for Estimates of N<sub>2</sub>O and CH<sub>4</sub> Emissions

Development of a continuous UAV-mounted air sampler and application to the quantification of CO2 and CH4 emissions from a major coking plant

UAV Based In situ Measurements of CO2 and CH4 Fluxes over Complex Natural Ecosystems

Using metal oxide gas sensors to estimate the emission rates and locations of methane leaks in an industrial site: assessment with controlled methane releases

The IAGOS-core Greenhouse Gas Package: a Measurement System for Continuous Airborne Observations of CO2, CH4, H2O and CO

UAV-based in situ measurements of CO2 and CH4 fluxes over complex natural ecosystems

A UAV-based Active AirCore System for Measurements of Greenhouse Gases

Characterization of a Commercial Lower-Cost Medium-Precision Non-Dispersive Infrared Sensor for Atmospheric CO2 Monitoring in Urban Areas

Development of Methods for Top-Down Methane Emission Measurements of Oil and Gas Facilities in an Offshore Environment Using a Miniature Methane Spectrometer and Long-Endurance Uncrewed Aerial System

Reconstruction of High-Frequency Methane Atmospheric Concentration Peaks from Measurements Using Metal Oxide Low-Cost Sensors

Development and deployment of a mid-cost CO2 sensor monitoring network to support atmospheric inverse modeling for quantifying urban CO2 emissions in Paris