Abstract:Purpose This study aims to investigate the machining performance of CVD-coated carbide tools by considering most crucial machinability aspects: cutting force, tool life, surface roughness and chip morphology in high-speed hard turning of AISI 4340 alloy steel under a sustainable minimum quantity lubrication (MQL) environment. Design/methodology/approach The purpose of this study is to analyze the performance of coated carbide tools under MQL environment therefore, machining tests were performed in accordance with the Taguchi L9 orthogonal array, accommodating the three crucial machining parameters such as cutting speed (V = 300–400 m/min), feed rate (F = 0.1–0.2 mm/rev) and depth of cut (DOC = 0.2–0.4 mm). The measured or calculated values obtained in each experimental run were validated for normality assumptions before drawing any statistical inferences. Taguchi signal-to-noise (S/N) ratio and analysis of variance methodologies were used to examine the effect of machining variables on the performance outcomes. Findings The quantitative analysis revealed that the depth of cut exerted the most significant influence on cutting force, with a contributing rate of 60.72%. Cutting speed was identified as the primary variable affecting the tool life, exhibiting a 47.58% contribution, while feed rate had the most dominating impact on surface roughness, with an overall contributing rate of 89.95%. The lowest cutting force (184.55 N) and the longest tool life (7.10 min) were achieved with low machining parameters at V = 300 m/min, F = 0.1 mm/rev, DOC = 0.2 mm. Conversely, the lowest surface roughness (496 nm) was achieved with high cutting speed, low feed rate and moderate depth of cut at V = 400 m/min, F = 0.1 mm/rev and DOC = 0.3 mm. Moreover, the microscopic examination of the chips revealed a serrated shape formation under all machining conditions. However, the degree of serration increased with an incremental raise with cutting speed and feed rate. Research limitations/implications The study is limited to study the effect of machining parameters within the stated range of cutting speed, feed rate and depth of cut as well as other parameters. Practical implications Practitioners may consider to adopt this machining technique to create more sustainable working environment as well as eliminate the disposal cost of the used metal cutting fluid. Social implications By applying this machining technique, diseases caused by metal cutting fluid to the mechanist will be significantly reduced, therefore creating better lifestyles. Originality/value Hard turning is commonly carried out with advanced cutting tools such as ceramics, cubic boron nitride and polycrystalline cubic boron nitride to attain exceptional surface finish. However, the high cost of these tools necessitates exploration of alternative approaches. Therefore, this study investigates the potential of using cost-effective, multilayer-coated carbide tools under MQL conditions to achieve comparable surface quality. Peer review The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-01-2024-0013/

Sustainable machining of AISI 4340 steel using semi-vegetable oil blends

Minimum quantity blended bio-lubricants for sustainable machining of superalloy: An MCDM model-based study

Influence of Mango Seed Oil on Surface Roughness and Cutting Temperature During Sustainable Turning of AISI 1525 Steel Under Minimum Quantity Lubrication Environment

Tool wear analysis in AISI 52100 steel machining with sustainable approach

Development of novel sustainable neat-oil metal working fluids for stainless steel and titanium alloy machining. Part 1. Formulation development

Biodegradable cutting fluids for sustainable manufacturing: a review of machining mechanisms and performance

Sustainability assessment associated with surface roughness and power consumption characteristics in nanofluid MQL-assisted turning of AISI 1045 steel

Thermophysical, tribological, and machinability characteristics of newly developed sustainable hybrid lubri-coolants for milling Ti-6Al-4V

Exploring the viability of alternative cooling-lubrication strategies in machining processes: A comprehensive review on the performance and sustainability assessment

A Study on the Machinability and Environmental Effects of Milling AISI 5140 Steel in Sustainable Cutting Environments

Green Lubricants in Action: A Comprehensive Performance Evaluation of Groundnut Oil-Based Cutting Fluids in Metal Machining Processes

Tribological and Morphological Study of AISI 316L Stainless Steel during Turning under Different Lubrication Conditions

High-speed turning of AISI 4340 alloy steel using carbide tools in a sustainable minimum quantity lubrication environment

Influence of MoS2-Based Nanofluid Minimum Quantity Lubrication on Machining Performance of AISI 316L Stainless Steel

Performance assessment of mahogany oil-based cutting fluid in turning AISI 304 steel alloy

Assessing the lubrication performance of various vegetable oil-based nano-cutting fluids via eco-friendly MQL technique in drilling of AISI 321 stainless steel

A Review of High-Speed Turning of AISI 4340 Steel with Minimum Quantity Lubrication (MQL)

Performance and Life Cycle Analysis of Soybean Oil-Based Minimum Quantity Lubrication in Machining of Ti6Al4V

Comparative performance studies of turning 4140 steel with TiC/TiCN/TiN-coated carbide inserts using MQL, flooding with vegetable cutting fluids, and dry machining

Sustainable machining of superalloy in minimum quantity lubrication environment: leveraging GEP-PSO hybrid optimization algorithm

A Study on the Effects of Hybridized Metal Oxide and Carbonaceous Nano-Cutting Fluids in the End Milling of AA6082 Aluminum Alloy