Abstract:Purpose This study aims to investigate the machining performance of CVD-coated carbide tools by considering most crucial machinability aspects: cutting force, tool life, surface roughness and chip morphology in high-speed hard turning of AISI 4340 alloy steel under a sustainable minimum quantity lubrication (MQL) environment. Design/methodology/approach The purpose of this study is to analyze the performance of coated carbide tools under MQL environment therefore, machining tests were performed in accordance with the Taguchi L9 orthogonal array, accommodating the three crucial machining parameters such as cutting speed (V = 300–400 m/min), feed rate (F = 0.1–0.2 mm/rev) and depth of cut (DOC = 0.2–0.4 mm). The measured or calculated values obtained in each experimental run were validated for normality assumptions before drawing any statistical inferences. Taguchi signal-to-noise (S/N) ratio and analysis of variance methodologies were used to examine the effect of machining variables on the performance outcomes. Findings The quantitative analysis revealed that the depth of cut exerted the most significant influence on cutting force, with a contributing rate of 60.72%. Cutting speed was identified as the primary variable affecting the tool life, exhibiting a 47.58% contribution, while feed rate had the most dominating impact on surface roughness, with an overall contributing rate of 89.95%. The lowest cutting force (184.55 N) and the longest tool life (7.10 min) were achieved with low machining parameters at V = 300 m/min, F = 0.1 mm/rev, DOC = 0.2 mm. Conversely, the lowest surface roughness (496 nm) was achieved with high cutting speed, low feed rate and moderate depth of cut at V = 400 m/min, F = 0.1 mm/rev and DOC = 0.3 mm. Moreover, the microscopic examination of the chips revealed a serrated shape formation under all machining conditions. However, the degree of serration increased with an incremental raise with cutting speed and feed rate. Research limitations/implications The study is limited to study the effect of machining parameters within the stated range of cutting speed, feed rate and depth of cut as well as other parameters. Practical implications Practitioners may consider to adopt this machining technique to create more sustainable working environment as well as eliminate the disposal cost of the used metal cutting fluid. Social implications By applying this machining technique, diseases caused by metal cutting fluid to the mechanist will be significantly reduced, therefore creating better lifestyles. Originality/value Hard turning is commonly carried out with advanced cutting tools such as ceramics, cubic boron nitride and polycrystalline cubic boron nitride to attain exceptional surface finish. However, the high cost of these tools necessitates exploration of alternative approaches. Therefore, this study investigates the potential of using cost-effective, multilayer-coated carbide tools under MQL conditions to achieve comparable surface quality. Peer review The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-01-2024-0013/

Tool wear analysis in AISI 52100 steel machining with sustainable approach

Comparison of Tool Wear, Surface Roughness, Cutting Forces, Tool Tip Temperature, and Chip Shape during Sustainable Turning of Bearing Steel

Sustainable machining of AISI 4340 steel using semi-vegetable oil blends

Effect of Surface Texture Tools and Minimum Quantity Lubrication (MQL) on tool Wear and Surface Roughness in CNC Turning of AISI 52100 Steel

Exploring the viability of alternative cooling-lubrication strategies in machining processes: A comprehensive review on the performance and sustainability assessment

Sustainability Assessment and Machinability Investigation of Austenitic Stainless Steel in Finish Turning with Advanced Ultra-Hard SiAlON Ceramic Tool under Different Cutting Environments

A Study on the Machinability and Environmental Effects of Milling AISI 5140 Steel in Sustainable Cutting Environments

Integrating textured tools and diverse lubricooling approaches in machining performance of Ti and Ni-base alloys – a comprehensive review

Measurement of machining characteristics under novel dry ice blasting cooling assisted milling of AISI 52100 tool steel

Tribological and Morphological Study of AISI 316L Stainless Steel during Turning under Different Lubrication Conditions

Sustainability assessment associated with surface roughness and power consumption characteristics in nanofluid MQL-assisted turning of AISI 1045 steel

Experimental investigations on surface integrity and chip morphology in hard tuning of AISI D3 steel under sustainable nanofluid-based minimum quantity lubrication

Tool wear mechanisms and its influence on machining tribology of face milled titanium alloy under sustainable hybrid lubri-cooling

Experimental and 3D-Deform Finite Element Analysis on Tool Wear during Turning of Al-Si-Mg Alloy

Experimental Investigation and Performance Optimization during Machining of Hastelloy C-276 Using Green Lubricants

State of the art review on the sustainable dry machining of advanced materials for multifaceted engineering applications: Progressive advancements and directions for future prospects

The use of machine learning and metaheuristic algorithm for wear performance optimization of AISI 1040 steel and investigation of corrosion resistance

Performance improvement of turning operation during processing of AISI 304 with novel textured tools under minimum quantity lubrication using hybrid optimization technique

Machining performance evaluation and tool wear analysis of dry cutting austenitic stainless steel with variable-length restricted contact tools

High-speed turning of AISI 4340 alloy steel using carbide tools in a sustainable minimum quantity lubrication environment