Abstract:This study investigated the metallurgical, mechanical properties and quality of coatings fabricated by direct laser metal deposition (DLMD) on Ti-6Al-4V, which were affected by the DLMD optimized process parameters. A 3-kW continuous wave ytterbium laser system (YLS) attached to a KUKA robot was used for the process. An analysis was conducted to determine the quality of the coatings in terms of hardness and wear resistance. Variables such as the time of interlayer deposition, thickness of the substrate, the initial temperature of the substrate, and the number of deposited layers were also investigated. The independent/collective effect that each process parameter had on the metallurgical and mechanical properties of the deposited Ti-6Al-4V were made clear when the processing parameters were varied. Minute pores/defects that significantly affect the metallurgical and mechanical properties of clads were also identified. The results obtained from the designed experiments showed that the depth of Heat Affected Zone (HAZ) was inversely proportional to the thickness of the substrate; as the thickness of the substrate was increased, the HAZ depth decreased. Moreover, the intensity of the laser power also affects the HAZ depth. In addition, it was discovered that the initial conditions of the substrate at room temperature also affected the coatings in relation to pre-heated conditions. The analysis conducted in identifying and quantifying the porosity showed indication that the factors such as scanning speed, laser power and powder feed rate had a predominant influence on the porosity. The grain form and structure as well as the mechanical properties of the cladded layer were significantly affected by the optimized process parameters of DLMD process. The parameters investigated had a significant impact on the hardness and wear resistance performance. Furthermore, the results revealed that the highest hardness of one of the coatings was 1.97-times the substrate which had a hardness value of 302 HV. The outstanding wear resistance performance of Al-Si-Sn-Cu/Ti-6Al-4V composite coating is attributed to major hard intermetallic phases.

Influence of post processing on the mechanical properties and wear behavior of selective laser melted Co-Cr-Mo-W alloys

CoCr alloy processed by Selective Laser Melting (SLM): effect of Laser Energy Density on microstructure, surface morphology, and hardness

Morphology and Properties of CoCrMo Parts Fabricated by Selective Laser Melting

Effect of Post-Heat Treatment Cooling Conditions on Microstructures and Fatigue Properties of Cobalt Chromium Molybdenum Alloy Fabricated through Selective Laser Melting

Effects of thermal treatments on microstructure and mechanical properties of a Co-Cr-Mo-W biomedical alloy produced by laser sintering

Microstructural, Mechanical, and Tribological Characterization of Selective Laser Melted CoCrMo Alloy under Different Heat Treatment Conditions and Hot Isostatic Pressing

Effect of scan speed on corrosion and tribocorrosion properties of cobalt-chromium alloy in situ produced by selective laser melting

Effects of heat treatment on the microstructure, residual stress, and mechanical properties of Co-Cr alloy fabricated by selective laser melting

Selective laser melting of CuCrZr alloy: processing optimisation, microstructure and mechanical properties

Effect of grain boundary character on isothermal phase transformation and mechanical properties of Co-Cr-Mo alloy fabricated by selective laser melting

Data related to optimized process parameters influence on hardness, microstructural evolution and wear resistance performance of Al-Si-Sn-Cu/Ti-6Al-4V composite coatings

Microstructure evolution and mechanical properties of Al-Al2O3 composites fabricated by selective laser melting

Effect of heat treatment on microstructure and mechanical properties of Fe–Cr–Ni–Co–Mo maraging stainless steel produced by selective laser melting

Influence of Scanning Strategy and Post-Treatment on Cracks and Mechanical Properties of Selective-Laser-Melted K438 Superalloy

Investigation of Impact Strength, Micro Hardness and Metallurgical Analysis of DMLS Fabricated CoCrMo Alloy Samples

Study of the microstructure and wear properties of Ti-12Mo-6Zr-2Fe alloy fabricated via selective laser melting

Experimental and numerical study on micro-milling of CoCrW alloy produced by selective laser melting and casting

The manufacturing process optimization and the mechanical properties of FeCoCrNi high entropy alloys fabricated by selective laser melting

Tailoring the tribology property and corrosion resistance of selective laser melted CoCrMo alloys by varying copper content

Role of laser remelting and heat treatment in mechanical and tribological properties of selective laser melted Ti6Al4V alloy

Tensile, hardness and metallurgical analysis of laser cured Co-Cr-Mo alloy samples