Abstract:When a pump operates in part-load conditions, it is apt to form flow separations and even stall cells at the blade surfaces. In some conditions, stall cells may circumferentially propagate among the blade channels, known as rotating stall, which can affect the rotor system dynamic stability. Conventionally it is believed that the formation and circumferential propagation of stall cells is attributed to the nonuniformity of the flow state in front of the impeller inlet. In recent decades, many investigations indicate that the uneven flow field at the impeller outlet related to the asymmetric volute casing is also an important factor to induce rotating stalls. Thus the formation and propagation mechanism of rotating stalls is complex and has not been clearly understood so far. In addition, previous studies mainly focused on the rotating stalls in vaned diffusers, while it is more difficult to figure out rotating stalls in impellers for which little studies has been done. In this paper, numerical simulations are conducted for a three-blade centrifugal pump with a flow rate of 0.75Qd where Qd is the design flow rate. The SST-SAS model with a curvature correction is applied to predict the unsteady internal flows. The time-averaged pump head, efficiency and axial power agree well with the experimental results from a previous test. From the numerical results, a special rotating stall is detected in this condition. In order to verify the effect of the volute casing, a contrast simulation is also conducted without the volute casing domain. It shows that rotating stalls always occur whether there is a volute casing or not, but the distribution and motion of the stall cells are changed by the existence of the volute casing. It indicates that the nonuniform flow distribution at the impeller outlet is not an essential factor for the formation of rotating stall but accelerates the variation of stall cells. Based on the whole-flow-passage result, a stall cell in one blade channel disappears for about 2/15T (T is the duration of one revolution) when the downstream blade runs across the tongue, and the same phenomenon recurs in the upstream blade channel after 1/3T, which is unusual and worthy of investigation. The pressure fluctuations within the whole flow passage are intensified by the rotating stall more or less, especially at the middle region of pressure surface of blades, around the tongue and in the beginning of the discharge passage.

Temperature Gradient Effects on Stator Boundary-Layer Stability in a Rotor–Stator Cavity

Study on transition to turbulence of rotating-disk boundary layer in a rotor-stator cavity with temperature gradient

Numerical investigation on the flow and heat transfer in a rotor-stator disc cavity

Influence of Rotor-Stator Interaction on Flow Stability in Centrifugal Pump Based on Energy Gradient Method

Experimental Investigation of Heat Transfer in a Rotor–stator Cavity with Cooling Air Inlet at Low Radius

Investigations of an Enclosed Annular Rotor-Stator System with LES Method

Turbulence characteristics of the Bödewadt layer in a large enclosed rotor-stator system

Stability Analysis of Symmetrical Rotors Partially Filled with a Viscous Incompressible Fluid

The Numerical Simulation Of Turbulent Flow In Semi-Closed Rotor Stator Cavity

Numerical Investigation of the Turbulent Wake-Boundary Interaction in a Translational Cascade of Airfoils and Flat Plate

Instabilities of rotating inclined buoyancy layers

Experimental Investigation on the Flow and Flow-Rotor Heat Transfer in a Rotor-Stator Spinning Disk Reactor

Numerical Investigation on the Rotating Stall Characteristics in A Three-Blade Centrifugal Impeller

Curvature effect on the instabilities of lid-driven flow in a toroidal square cavity

Linear stability analysis of cylindrical Rayleigh–Bénard convection

Investigation Of The Unstable Flow Structure In A Rotating Cavity

Numerical Investigation and Experimental Verification of the Fluid Cooling Process of Typical Stator–Rotor Machinery with a Plate-Type Heat Exchanger

The Role of Density Gradient in Species Migration and Secondary Flow Structures in Axial Flow Turbines

NUMERICAL INVESTIGATION OF DIFFUSER FLOW FIELD AND ROTATING STALL IN A CENTRIFUGAL COMPRESSOR WITH VANED DIFFUSER

Numerical investigation of the boundary layer stability on a section of a rotating wind turbine blade

Numerical Study on Rotating Characteristics of Unsteady Flow Inner Pump-turbine in Pump Mode