Abstract:Purpose: The aim of the proposed research is to establish experimentally the relation between damaging of the tread surface of model wheels and the characteristics of fatigue crack growth resistance of wheel steels "KI th, "KII th, "KI fc, "KII fc), depending on its microstructure. Design/methodology/approach: Characteristics of the fatigue crack growth resistance have been determined on the specimens cut out from the hot rolled plate of thickness 10 mm of the steel which is an analogue of railway wheel steels. To obtain different steel microstructures and its strength level, test specimens were quenched (820°C, in oil) and then tempered at 400°C, 500°C, and 600°C for 2 h. The characteristics of Mode I fatigue crack growth resistance of steel were determined on the basis of fatigue macrocrack growth rate diagrams da/dN–"KI, obtained by the standard method on compact specimens with the thickness of 10 mm at a frequency of 10-15 Hz and the stress ratio R = 0.1 of the loading cycle. The characteristics of Mode II fatigue crack growth resistance were determined on the basis of da/dN–"KII diagrams, obtained by authors method on edge notched specimens with the thickness 3.2 mm at a frequency of 10-15 Hz and R = –1 taking account of the crack face friction. The hardness was measured with a TK-2 hardness meter. Zeiss-EVO40XVP scanning electron microscope was used for microstructural investigations. Rolling contact fatigue testing was carried out on the model specimens of a wheel of thickness 8 mm and diameter 40 mm in contact with a rail of length 220 mm, width 8 mm and height 16 mm. Wheels were manufactured form the above-described steel after different treatment modes. Rails were cut out from a head the full-scale rail of hardness 46 HRC. The damaging was assessed by a ratio of the area with gaps formed by pitting and spalling to the general area of the wheel tread surface using a special stand. Findings: The growth of the damage of the tread surface of the model wheels correlates uniquely with the decrease of the cyclic fracture toughness of the wheel steel "KI fc and "KII fc, determined at Mode I and Mode II fracture mechanisms. These characteristics of the wheel steel can be considered as the determining parameter of this process, in contrast to the fatigue thresholds "KI th and "KII th. Research limitations/implications: Investigations were conducted on model wheels that simulate the damage of real railway wheels tread surface. Practical implications: A relationship between the damage of tread surface of railway wheels and the strength level of wheel steels is determined. Originality/value: The damage of the tread surface of the model wheels during the rolling contact fatigue of the pair wheel-rail increases with the growth of the strength (hardness) of the wheel steel, which corresponds to the statistical data of the operation of the real railway wheels.

Addressing perceptions regarding the influence of relative hardness on wheel/rail performance

The effects of hardness on the spalling property of railway wheel steel

Effect of Mechanical Properties of Rail and Wheel on Wear and Rolling Contact Fatigue

Initiation and evolution of wheel polygonal wear: Influence of wheel-rail hardness ratios

Investigation on the transient rolling contact behaviour of corrugated rail considering material work hardening

Effect of material hardness ratio on wear and rolling contact fatigue: Development and validation of new laws

Investigation on wear and rolling contact fatigue of wheel-rail materials under various wheel/rail hardness ratio and creepage conditions

Effects of Abrasive Material and Hardness of Grinding Wheel on Rail Grinding Behaviors

Influence of thermal loading parameters and microstructure on the formation of stratified surface layers on railway wheels

The effect of third bodies on wear and friction at the wheel-rail interface

The effect of strain hardening on shakedown limits of a pearlitic rail steel

Relationships between the fatigue crack growth resistance characteristics of a steel and the tread surface damage of railway wheel

Effect of normal load on the wear and rolling contact fatigue behaviour of AAR class B wheel against R350HT rail in a twin disc simulator

Influence of material properties on the high-speed wheel-rail rolling contact behaviour

Characterization of the Microstructure Changes Induced by a Rolling Contact Bench Reproducing Wheel/Rail Contact on a Pearlitic Steel

Experimental Investigation on the Wear and Damage Behaviors of Machined Wheel-Rail Materials under Dry Sliding Conditions

New insight into the dry rolling-sliding wear mechanism of carbide-free bainitic and pearlitic steel

Evolution of microscopic characteristics of rolling contact fatigue coexisting with wear of U75V rail

Wheel-rail contact and friction models: A review of recent advances

Wear Problems of High-Speed Wheel/Rail Systems: Observations, Causes, and Countermeasures in China

Stratified surface layers affecting crack propagation in wheel-rail contacts