Abstract:Coal liquefaction residue (CLR) has a high content of carbon and organic substances. However, sulfur and inorganics pose a challenge for the high-value-added utilization of CLR. In this work, general-purpose carbon fiber was successfully prepared by the new method of chlorination–dechlorination using CLR as raw material and benzyl chloride as chlorinating agent. The effect of benzyl chloride addition amount on the property of isotropic pitch precursor and the performance of general-purpose carbon fiber were investigated. The results showed that the as-prepared pitch precursors were dominated by carbon elements and contained small numbers of hydrogen, oxygen, nitrogen, and sulfur. The characteristic peaks generated from chlorine elements were observed in both FTIR and XPS spectra. The peaks at the wavenumbers of 1490 cm −1 and 696 cm −1 corresponded to the vibration of C–Cl bond, and a tiny Cl 2p peak located at 200.0 eV was observed by reducing the noise of XPS spectra. It indicates that the trace chlorine remains in the as-synthesized isotropic pitch precursor even after undergoing dechlorination. The molecular compositions of isotropic pitches were mainly polyaromatic hydrocarbons, and the chlorination–dechlorination promotes the oligomerization of polyaromatic hydrocarbons to form dimers and trimers. Therefore, the polycondensed degree and carbon aromaticity were improved. It is known from 13 C NMR analysis that the effect of chlorine–dechlorination makes the molecular structure of pitches transform more linear, thus enhancing their spinnability. In addition, the higher the amount of benzyl chloride added, the better the property of isotropic pitch was. The pitch of BC-30 and BC-40 showed excellent spinnability, stabilized property, and carbonized property compared to other pitches. The morphology of obtained carbon fiber was homogeneous and smooth without defects in surface and section. The as-prepared general-purpose carbon fiber demonstrated good tensile strength up to 1220 MPa with an average diameter of 8.5 μm.

Reformation of Naphtha Cracking Bottom Oil for the Preparation of Carbon Fiber Precursor Pitch

Spinnable Mesophase Pitch Prepared via Co-carbonization of Fluid Catalytic Cracking Decant Oil and Synthetic Naphthalene Pitch

Effect of oxygen-introduced pitch precursor on the properties and structure evolution of isotropic pitch-based fibers during carbonization and graphitization

Preparation of pitch precursor with excellent spinnability for general-purpose carbon fibre using coal tar pitch as raw material

Controllable Preparation of Spinnable Isotropic Pitches for Carbon Fibers with High Tensile Strength from Low-Cost Ethylene Tar Pitch by a Selective Photobromination–debromination Method

Mesophase pitch raw material used for preparing high-modulus high-thermal-conductivity carbon fiber, and preparation method thereof

Co‐Carbonization of Medium‐ and Low‐Temperature Coal Tar Pitch and Coal‐Based Hydrogenated Diesel Oil Prepare Mesophase Pitch for Needle Coke Precursor

Preparation of Mesophase Pitch with Fine-Flow Texture from Ethylene Tar/Naphthalene by Catalytic Synthesis for High-Thermal-Conductivity Carbon Fibers

Chemical Activation Characteristics of Pitch-Based Carbon Fibers by KOH

Preparation of Isotropic Carbon Fibers from Kerosene-Purified Coal Tar Pitch by Co-Carbonization with Pyrolysis Fuel Oil

Enhancing spinnability and properties of carbon fibers through modification of isotropic coal tar pitch precursor

Effects of Bromination-Dehydrobromination on the Microstructure of Isotropic Pitch Precursors for Carbon Fibers

Preparation and characterization of pitch coke from oxidized polymerized pitch

Structure and composition of mesophase pitch prepared from aromatic‐rich fluid catalytic cracking slurry under different process conditions

Research progress in the preparation of mesophase pitch from fluid catalytic cracking slurry

Effects of co-carbonization of medium and low temperature refined pitch and high temperature refined pitch on the structure and properties of needle coke

Exploration of fibers produced from petroleum based-mesophase pitch and pet blends for carbon fiber production

Constructing the Bridge from Isotropic to Anisotropic Pitches for Preparing Pitch-Based Carbon Fibers with Tunable Structures and Properties

Controllable synthesis of isotropic pitch precursor for general purpose carbon fiber using waste ethylene tar via bromination–dehydrobromination

Preparation of spinnable mesophase pitch from pyrolyzed fuel oil by pressurized heat treatment and its application of carbon fiber

Chlorination–dechlorination of coal liquefaction residue using benzyl chloride for general-purpose carbon fiber synthesis