Abstract:The prevention of hot cracking formation is of utmost importance in the production of the new Ni-Co based superalloys through the utilization of the electron beam smelting layered solidification technique (EBSL), as it ensures exceptional homogeneity and dependable consistency of the specimens. In contrast to previous studies that focused on minimizing the liquid film and solidification range, our methodology adopts a distinct approach. In this research, a novel methodology was employed to mitigate internal stresses through the implementation of equiaxed grain layers via an alternately reduced cooling method. This ultimately resulted in the elimination of hot cracking. To be more specific, the transition from a columnar to an equiaxed structure was observed during the layer-by-layer construction process in the fabrication of the new Ni-Co based superalloy in EBSL. The EBSL-Ni-Co superalloy, when subjected to the alternating reduction cooling method, exhibited an internal stress of 49 MPa. This value represents a significant reduction of 83.8% compared to the internal stress observed when employing the linear reduction cooling method. Additionally, the solvus temperature of the gamma - gamma ' eutectic phases in EBSL-Ni-Co superalloys produced by the alternating reduction cooling method is significantly higher. Intriguingly, the N th layer of the EBSL-Ni-Co based superalloys produced by EBSL simultaneously heats treated with the preceding layers. And the low melting point phase gradually dissolved back into the matrix. The implementation of an alternating reduced cooling method successfully mitigated the formation of the liquid film in the gamma - gamma ' eutectic phase and the buildup of internal stresses in the EBSL-Ni-Co superalloy during its manufacturing process. These discoveries open up a novel preparation procedure pathway for the manufacture of crack-free superalloys with superior mechanical characteristics using EBSL. (c) 2023 Published by Elsevier Ltd on behalf of The editorial office of Journal of Materials Science & Technology.

Microstructure Control and Hot Cracking Prevention During Laser Additive Manufacturing of Cobalt-Based Superalloy

Mechanical Properties and Fracture Behavior of Laser Powder-Bed-Fused GH3536 Superalloy

Hot cracking behavior and mechanism of the IC10 directionally solidified superalloy during laser re-melting

The mechanism and regulation of hot cracking in a new complex-concentrated alloy by a novel integrated directed energy deposition

Origin of hot cracking formation and suppression method in laser additive manufactured nickel-based superalloys

Research about the Microcrack Mechanisms in Molybdenum and Corresponding Suppression Strategies During Laser Additive Manufacturing Process

Microstructure Control and Hot Cracking Behavior of the New Ni-Co Based Superalloy Prepared by Electron Beam Smelting Layered Solidification Technology

Crack Inhibition and Performance Modification of NiCoCr-Based Superalloy with Y2O3 Nanoparticles by Laser Metal Deposition

Elimination of hot cracking in the laser surface re-melting of the IC10 superalloy by controlling the heat input

Hot Crack Formation Mechanism and Inhibition of a Novel Cobalt-Based Alloy Coating during Laser Cladding

Mitigating hot-cracking of laser melted CoCrFeNiMnTix high-entropy alloys

Microalloying Design in Directed Energy Deposition of Complex-Concentrated Alloy: Pre-Nitriding to Inhibit Hot Cracking and Promote Mechanical Properties

Investigation on the hot crack sensitivity of a nickel-based single crystal superalloy fabricated by epitaxial laser metal forming

Hot cracking behavior and mechanism of a third-generation Ni-based single-crystal superalloy during directed energy deposition

Avoiding Cracks in Additively Manufactured Non-Weldable Directionally Solidified Ni-based Superalloys

Crack Formation and Control in an AlCoCrFeNi High Entropy Alloy Fabricated by Selective Laser Melting

Cracking in Laser Additively Manufactured W: Initiation Mechanism and a Suppression Approach by Alloying

The Effect of Thermal Cycle on Hot Cracking Evolution and Formation Mechanism in Thin Wall, Single Layer, and Cubic Samples of High-Strength Al-Cu-Mg-Mn Alloys Fabricated by Laser Powder Bed Fusion

Influences of Cooling Conditions on the Liquation Cracking in Laser Metal Deposition of a Directionally Solidified Superalloy

Liquefaction Characteristics and Cracking Behavior of the Grain Boundaries and Interdendritic Regions in Non-Weldable K447A Superalloy During Laser Re-Melting

Research on hot cracking in laser welding of Al-contaminated CoCrFeMnNi high-entropy alloys