Abstract:In the reported low-fluorine MOD-YBCO studies, the lowest F/Ba mole ratio of the precursor solution was 4.5. However, further lowering the F/Ba ratio is important according to the researches of YBCO thick film. On the other hand, the F/Ba ratio is necessary to be at least 2 for the full conversion of the Ba precursor to BaF_2 to avoid the formation of BaCO_3, which is detrimental to the superconducting performance. In this study, a novel solution with the F/Ba mole ratio of 2 was developed, in which the fluorine content was only about 10.3% of that used in the conventional TFA-MOD method. Attenuated total reflectance-Fourier transformed-infrared spectra(ATR-FT-IR) revealed that BaCO_3 was remarkably suppressed in the as-pyrolyzed film and eliminated at 700 Celsius degree. Thus YBCO films with a critical current density (J_c) over 5 MA cm^{-2} (77 K, 0 T, 200 nm thickness) could be obtained on LAO single crystal substrates. In-situ FT-IR spectra showed that no obvious fluorinated gaseous by-products were detected in the pyrolysis step, which indicated that all of the F atoms might remain in the film as fluorides. X-ray diffraction (XRD) \theta/2\theta-scan showed that BaF_2, but neither YF_3 nor CuF_2, was detected in the films quenched at 400 - 800 Celsius degree. The formation priority of BaF_2 over YF_3 and CuF_2 was interpreted by the chemical equilibrium of the potential reactions. Our study could enlarge the synthesis window of the precursor solution for MOD-YBCO fabrication and open a gate to study the fluorine content in the precursor solution continuously and systematically.

YBCO Ceramic Nanofibers obtained by the new technique of Solution Blow Spinning

Successful production of solution blow spun YBCO+Ag complex ceramics

Solution Blow Spinning Control of Morphology and Production Rate of Complex Superconducting YBa2Cu3O7-x Nanowires

LaMnO3 and La0.875Sr0.125MnO3 Nanofibers via Electrospinning

LaMnO_3 and La_(0.875)Sr_(0.125)MnO_3 Nanofibers via Electrospinning

Effect of Solution Concentrations on the Structure and Properties of Nanofibrous Yarns by Blown Bubble-Spinning

Preparation of YIG Single Crystal Nanofibers Via an Electrospinning Technique

A Mixed Solvent Approach to Make Poly(vinylidene Fluoride) Nanofibers with High Β-Phase Using Solution Blow Spinning

Electrospinning of pure polymer-derived SiBCN nanofibers with high yield

One-dimensional electrospun alumina borate ceramics: transformation from fiber-like structure to ribbon-like structure at the increased concentrations of precursor sol

Fine-diameter Si–B–C–N ceramic fibers enabled by polyborosilazanes with N–methyl pendant group

Magneto-resistivity and magnetization investigations of YBCO superconductor added by nano-wires and nano-particles of titanium oxide

A Low-Fluorine Solution with the F/Ba Mole Ratio of 2 for the Fabrication of YBCO Films

Fabrication Of Micro Yarn Composed Of Nanofibers By Blown Bubble Spinning

In situ high temperature optical microscopy study of phase evolution in YBa 2 Cu 3 O 7 d films prepared by a fluorine-free sol – gel route

Advances in Biomedical Applications of Solution Blow Spinning

Chemical Solution Deposition of YBCO Films with Gd Excess

Microstructure and superconductivity of highly ordered YBa 2Cu3O7-δ nanowire arrays

Solution blow spinning mass production of mullite nanofiber from environment friendly aqueous Al–Si solutions

Study On Structure And Magnetic Properties Of Y-2(Fe, Co)(14)B Melt-Spun Ribbons

Blowspinning: A New Choice for Nanofibers.