Abstract:Carbon fibers (CFs) have been widely used as reinforcing materials because of their excellent specific strength, specific modulus, corrosion resistance, energy absorption, and other properties. To improve the mechanical properties of CF-reinforced composites, one of the effective methods is to improve the interfacial force between the CF and the polymer through modification of CFs. The aim of this study is to modify the surface of the CF with an environmentally friendly and efficient way and to design a continuous production equipment. In this research, a continuous electro-polymerization equipment was designed, and the surface of the CFs was modified by epoxy or vinyl ether, which was initiated by photoinitiator UVI-6974 without adding any solvent and extra electrolytes. By changing the structure of monomers, polymerization time, voltage, concentration of the initiator, and the distance between CFs and electrodes, the performance and thickness of the polymer layer on the CFs were controllable. The results of scanning electron microscopy and infrared spectroscopy proved that the surface of the CFs was covered by polymers, and some unreacted functional groups remained. The mechanical performances of CF composites prepared from the BDE/DVE-3-modified CFs showed that the interlaminar shear strength improved by 46.98 and 62.02%, and the tensile strength improved by 11.40 and 16.62%, respectively, compared with unmodified CFs. This proved that the interface force between the resin and the CF was greatly improved by the thin polymer layer on the surface of the CF and the unreacted functional groups. On the other hand, if pigments or dyes were added to the polymerization system, colored CFs could be fabricated by this equipment continuously. Because of the solvent-free, low-voltage, and continuous fabrication, this electro-polymerization method has a good industrial prospect.This article has not yet been cited by other publications.

Reversible surface modification of PAN-based carbon fibers by a ferrocene-based surfactant

Interfacial Modiﬁcation and Dispersion of Short Carbon Fiber and the Properties of Composite Papers As Gas Diffusion Layer for Proton Exchange Membrane Fuel Cell (PEMFC)

Influence of Carbon Nanotube Coatings on Carbon Fiber by Ultrasonically Assisted Electrophoretic Deposition on Its Composite Interfacial Property.

Co-depositing bio-inspired tannic acid-aminopropyltriethoxysilane coating onto carbon fiber for excellent interfacial adhesion of epoxy composites

Enhanced interfacial properties of hierarchical MXene/CF composites via low content electrophoretic deposition

Surface modification of carbon fibres with electroactive PEDOT/epoxy composites

Effect of Electrochemical Aryl Diazonium Salt Modification on Interfacial Properties of CF/PEEK Composites

Surface Modification of Carbon Fiber by Electro-Polymerization: Continuous Production, Thickness Control, Colorization, and Preparation of CFRP

Effect of surface functionalization on the surface and inter-facial properties of thermoplastic-coated carbon fibers

Modification on carbon fiber surface with pyrolytic deposition combined with PAMAM grafting

Functionalized carbon fibers with MXene via electrochemistry aryl diazonium salt reaction to improve the interfacial properties of carbon fiber/epoxy composites

On demand thermal surface modification of carbon fiber for improved interfacial shear strength

Surface modification of carbon fibers by anodic oxidation

Recycled carbon fiber reinforced composites: Enhancing mechanical properties through co-functionalization of carbon nanotube-bonded microfibrillated cellulose

A Novel Surface Modification of Carbon Fiber for High-Performance Thermoplastic Polyurethane Composites

Mussel-inspired modification of carbon fiber via polyethyleneimine/polydopamine co-deposition for the improved interfacial adhesion

Bio-inspired Polydopamine Functionalization of Carbon Fiber for Improving the Interfacial Adhesion of Polypropylene Composites

Enhancing the Mechanical properties of CF-Reinforced Epoxy Composites through Chemically Surface Modification of Carbon Fibers via Novel Two-Step Approach by Addition of Epichlorohydrin

Influence of surface modification of carbon fiber based on magnetron sputtering technology on mechanical properties of carbon fiber composites

Wettability of Carbon Fibers Modified by Acrylic Acid and Interface Properties of Carbon Fiber/Epoxy

Improved mechanical properties of carbon fiber/epoxy composites via fiber surface grafting of rigid-flexible chain structure