Abstract:In this study, the process of carbon dioxide (CO2) capture directly from ambient air in a conventional monoethanolamine (MEA) absorption process was simulated and optimized using a rate-based model in Aspen Plus. The process aimed to capture a specific amount (148.25 Nm3/h) of CO2 from the air, which was determined by a potential application aiming to produce synthetic methane from the output of a 2.7 MW electrolyser (593 Nm3/h H2). We investigated the technical performance of the process by conducting a sensitivity analysis around different parameters such as air humidity, capture rate defined as a ratio of moles of CO2 captured during the process to the total mole of CO2 in the feed stream, CO2 loading of lean and rich absorption liquids and reboiler temperature, and evaluated the energy consumption and overall cost in this system. In order to meet the design requirement for standard packed columns, the rich absorption liquid was circulated to the top of the absorber. A capture rate of 50% was selected in this process as a baseline. At higher capture rates, the required energy per ton of captured CO2 increases due to a higher steam stripping rate, required in the desorber, and at lower capture rates, the size of equipment, in particular, absorber and blowers increases due to the need for processing a significantly larger volume of air at the given CO2 production volume. At the base case scenario, a reboiler duty of 10.7 GJ/tCO2 and an electrical energy requirement of 1.4 MWh/tCO2 were obtained. The absorber diameter and height obtained were 10.4 and 4.4 m, respectively. The desorber is found to be relatively small at 0.54 m in diameter and 3.0 m in height. A wash water section installed at top of the absorber decreased the MEA loss to 0.28 kg/ton CO2. However, this increased capital cost by around 60% resulting in CO2 capture costs of $1,691 per ton CO2 for the MEA base scenario. Based on the techno-economic analysis, assuming a non-volatile absorbent rather than MEA thereby avoiding a wash water section, and using an absorption column built from cheaper materials, the estimated cost per ton of CO2 produced was reduced to $676/tCO2. The overall cost range was between $273 and $1,227 per ton of CO2 depending on different economic parameters such as electricity ($20–$200/MWh) and heat price ($2–$20/GJ), plant life (15–25 years) and capital expenditure (±30%). In order to reduce the cost further, the use of innovative cheap gas-liquid contactors that operate at lower liquid to gas ratios is crucial.

Multi-dimensional assessment for the novel carbon capture process integrated the low-temperature adsorption and desorption

Performance Exploration of Temperature Swing Adsorption Technology for Carbon Dioxide Capture

Comparative Analysis on Temperature Swing Adsorption Cycle for Carbon Capture by Using Internal Heat/mass Recovery

Design and performance evaluation of a novel system integrating Water-based carbon capture with adiabatic compressed air energy storage

Energy-efficient Process Intensification for Post-Combustion CO2 Capture: A Modeling Approach

Analysis on Temperature Vacuum Swing Adsorption Integrated with Heat Pump for Efficient Carbon Capture

Energy, Exergy, Economic and Environmental (4E) Analysis of an Integrated Process Combining CO2 Capture and Storage, an Organic Rankine Cycle and an Absorption Refrigeration Cycle

Steam-assisted Temperature Swing Adsorption for Carbon Capture Integrated with Heat Pump

Thermodynamic Exploration of Two-Stage Vacuum-Pressure Swing Adsorption for Carbon Dioxide Capture

Adsorption-based Post-Combustion Carbon Capture Assisted by Synergetic Heating and Cooling

Thermodynamics Analysis of Multi-Stage Temperature Swing Adsorption Cycle for Dilute CO2 Capture, Enrichment and Purification

Thermodynamic analysis of adsorption carbon capture from limiting cycle to heat pump assisted cycle

Techno-Economic Assessment for CO2 Capture From Air Using a Conventional Liquid-Based Absorption Process

Multistage Circulation Absorption Improvement: Simulation and Energy-Saving Evaluation of an Innovative Amine-Based CO2 Capture Process

Process design and adsorbent screening of VSA and exchanger type VTSA for flue gas CO 2 capture

Kinetics, Thermodynamics, and Mechanism of a Novel Biphasic Solvent for CO2 Capture from Flue Gas

MEA-based CO2 capture: a study focuses on MEA concentrations and process parameters

Design on CO<sub>2</sub> capture based on adsorption-absorption integration and energy storage for energy supply buildings with fixed carbon emission

Design on CO2 capture based on adsorption-absorption integration and energy storage for energy supply buildings with fixed carbon emission

Techno-economic Evaluation of Post-Combustion Carbon Capture Based on Chemical Absorption for the Thermal Cracking Furnace in Ethylene Manufacturing

New improvement of amine-based CO2 capture processes using heat integration and optimization