Abstract:Additive manufacturing, often known as three-dimensional (3D) printing, is a process in which a part is built layer-by-layer and is a promising approach for creating components close to their final (net) shape. This process is challenging the dominance of conventional manufacturing processes for products with high complexity and low material waste1. Titanium alloys made by additive manufacturing have been used in applications in various industries. However, the intrinsic high cooling rates and high thermal gradient of the fusion-based metal additive manufacturing process often leads to a very fine microstructure and a tendency towards almost exclusively columnar grains, particularly in titanium-based alloys1. (Columnar grains in additively manufactured titanium components can result in anisotropic mechanical properties and are therefore undesirable2.) Attempts to optimize the processing parameters of additive manufacturing have shown that it is difficult to alter the conditions to promote equiaxed growth of titanium grains3. In contrast with other common engineering alloys such as aluminium, there is no commercial grain refiner for titanium that is able to effectively refine the microstructure. To address this challenge, here we report on the development of titanium-copper alloys that have a high constitutional supercooling capacity as a result of partitioning of the alloying element during solidification, which can override the negative effect of a high thermal gradient in the laser-melted region during additive manufacturing. Without any special process control or additional treatment, our as-printed titanium-copper alloy specimens have a fully equiaxed fine-grained microstructure. They also display promising mechanical properties, such as high yield strength and uniform elongation, compared to conventional alloys under similar processing conditions, owing to the formation of an ultrafine eutectoid microstructure that appears as a result of exploiting the high cooling rates and multiple thermal cycles of the manufacturing process. We anticipate that this approach will be applicable to other eutectoid-forming alloy systems, and that it will have applications in the aerospace and biomedical industries.

Columnar-to-equiaxed transition mechanism and remarkable strengthening effect in additive manufactured pure titanium induced by copper addition

Enhancing Ductility of Titanium Matrix Composites by Multimodal Α-Grains

Additive manufacturing of titanium alloys with enhanced strength and uniform ductility via multi-element alloying

Achieving Enhanced Tensile Strength-Ductility Synergy Through Phase Modulation in Additively Manufactured Titanium Alloys

Effect of Cu content on microstructure and properties of Ti-6Al-4V alloy fabricated by double-wire arc additive manufacturing

Additive Manufacturing of Ultrafine-Grained High-Strength Titanium Alloys

Effect of Ti on Microstructure and Mechanical Properties of Die-Cast Al-Mg-Zn-Si Alloy

Additive manufacturing of fine-grain fully lamellar titanium aluminide alloys

Achieving superior strength-ductility combination in the heterogeneous microstructured Ti64 alloy via multi-eutectoid elements alloying with CoCrFeNiMn during laser powder bed fusion

Simultaneously Improved the Strength and Ductility of Cast Al-3Li-2Cu Alloy by Ti Addition and Heat Treatment

Fine Equiaxed Β Grains and Superior Tensile Property in Ti–6Al–4V Alloy Deposited by Coaxial Electron Beam Wire Feeding Additive Manufacturing

Martensite colony engineering: A novel solution to realize the high ductility in full martensitic 3D-printed Ti alloys

Contribution Made by Double-Sized TiC Particles Addition to the Ductility–strength Synergy in Wire and Arc Additively Manufactured Al–Cu Alloys

Face Centered Cubic Substructure and Improved Tensile Property in a Novel Β Titanium Alloy Ti–5Al–4Zr–10Mo–3Cr

Effect of Cu-induced Eutectoid Transformation on Microstructure and Mechanical Properties of Ti–6Al–4V Alloy by Laser Wire Deposition

Making Titanium Alloys Ultrahigh Strength and Toughness Synergy Through Deformation Kinks-Mediated Hierarchical Α-Precipitation

Additive manufacturing of a nanocrystalline lathy Ti6Al4V5Cu alloy with high strength and ductility combination

Al–Zn–Mg–Cu alloy with both high strength and high plasticity fabricated with wire arc additive manufacturing

Compositional and Microstructural Optimization and Mechanical-Property Enhancement of Cast Ti Alloys Based on Ti-6Al-4V Alloy

Realization of synergistic enhancement for fracture strength and ductility by adding TiC particles in wire and arc additive manufacturing 2219 aluminium alloy

Hierarchical microstructure and strain partition of a PM α + β titanium alloy with an ultrahigh strength-ductility synergy