Abstract:To improve the uncertainty of the aluminum fixed point, a study was launched by LNE-INM/CNAM in the framework of the EUROMET Project 732 “Toward more accurate temperature fixed points” (Coordinating laboratory: LNE-INM/CNAM, 17 partner countries). A new open cell was filled with aluminum of 99.99995% purity. A French laboratory carried out elemental analysis of the sample using glow discharge-mass spectrometry (GD-MS). The values of the equilibrium distribution coefficient k and of the derivative \documentclass[12pt]{minimal}\usepackage{amsmath}\usepackage{wasysym}\usepackage{amsfonts}\usepackage{amssymb}\usepackage{amsbsy}\usepackage{mathrsfs}\usepackage{upgreek}\setlength{\oddsidemargin}{-69pt}\begin{document}$${\delta T_{\rm{l}}/\delta c^{i}_{\rm{l}}}$$\end{document} of the temperature of the liquidus line with respect to the concentration of impurity i will be obtained through collaboration with a French physical and chemical laboratory. In the past, some aluminum cells were opened after several melts and freezes. The aluminum ingot was sticking to the graphite crucible, indicating that physicochemical reactions had likely occurred between Al and C. To avoid this reaction, an effort was made to draw benefit from the Al2O3 film that appears immediately on the surface of the aluminum ingot when it is exposed to oxygen. The open aluminum cell was tested in different furnaces and with different thermal insulator arrangements inside the fixed-point assembly. The observed drifts of the plateaux were always larger than the expected values. The cell was opened to inspect the aluminum ingot. The ingot was extracted easily, since no sticking to the crucible had occurred. The aluminum showed a very bright surface, but the presence of many “craters” throughout the thickness of the ingot was surprising. In some cases, the thermometer well was even apparent.

Influence of Chemically Active Additives on the Nature of the Evaporation of Highly Volatile Impurities during Their Determination in Aluminum and Its Oxide by Arc Atomic Emission Spectrometry

Effect of Aluminum Nanoparticles Addition on the Evaporation of a Monodisperse Ethanol Droplet Stream

Investigation of fluoride evaporation from CaF2–CaO–Al2O3–MgO–TiO2–(Li2O) slag for electroslag remelting

Experimental Measurement of Vacuum Evaporation of Aluminum in Ti-Al, V-Al, Ti6Al4V Alloys by Electron Beam

Quantitative Analysis of Complex Aluminum Electrolytes by X‐Ray Fluorescence

Xps Characterization of the Interface Between Low Dielectric Constant Amorphous Fluoropolymer Film and Evaporation-Deposited Aluminum

Theoretical aspects of fluoride air contaminant formation in aluminium smelter potrooms

Effect of CaF2 and CaO/Al2O3 ratio on evaporation and melting characteristics of low-fluoride CaF2–CaO–Al2O3–MgO–TiO2 slag for electroslag remelting

Structural correlation and chemistry of molten NaF–ScF3 with dissolved metal aluminium: TG/DTA, XRD, NMR and molecular dynamics simulations

Elimination of the contaminant fluoride ions from plant zinc sulfate electrolytes by aluminum sulfate

Electroanalytical methods for transition metal analysis in heavy metal fluoride melts

Study on Al Evaporation during AlV55 Melting and Alloy Preparation

A qualitative and quantitative investigation of nonmetallic inclusions in molten Al–Mg, Al–Cu, and Al–Zn–Mg–Cu alloys

Kinetics of Zinc Evaporation from Aluminium Alloys Melted Using VIM and ISM Technologies

Study on the dissolution of aluminium carbide formed on the graphite cathode in aluminium electrolysis

Investigation of the Interaction of Evaporated Aluminum with Vapor Deposited Teflon AF Films Via X-ray Photoelectron Spectroscopy

The Influence of Crucible Material on Aluminum Composition

Study of Corrosion-Electrochemical Behavior of Aluminum-Beryllium Alloys Alloyed with Yttrium, Lanthanum and Cerium

Impurity Behavior in Aluminum Extraction by Low-Temperature Molten Salt Electrolysis

Influence of Impurities and Filling Protocol on the Aluminum Fixed Point