Abstract:Low-density polyethylene (LDPE) films are widely used in packaging, insulation and many other commodity applications due to their excellent mechanical and chemical properties. However, the water-wetting and water-repellant properties of these films are insufficient for certain applications. In this study, bare LDPE and textured LDPE (T-LDPE) films were subjected to low-pressure plasmas, such as carbon tetrafluoride (CF4) and hydrogen (H2), to see the effect of plasma treatment on the wetting properties of LDPE films. In addition, the surface of the LDPE film was textured to improve the hydrophobicity through the lotus effect. The LDPE and T-LDPE films had contact angle (θ) values of 98.6° ± 0.6 and 143.6° ± 1.0, respectively. After CF4 plasma treatments, the θ values of the surfaces increased for both surfaces, albeit within the standard deviation for the T-LDPE film. On the other hand, the contact angle values after H2 plasma treatment decreased for both surfaces. The surface energy measurements supported the changes in the contact angle values: exposure to H2 plasma decreased the contact angle, while exposure to CF4 plasma increased the contact angle. Kinetic friction force measurements of water drops on LDPE and T-LDPE films showed a decrease in friction after the CF4 plasma treatment, consistent with the contact angle and surface energy measurements. Notably, the kinetic friction force measurements proved to be more sensitive compared to the contact angle measurements in differentiating the wetting properties of the T-LDPE versus 3× CF4-plasma-treated LDPE films. Based on Atomic Force Microscopy (AFM) images of the flat LDPE samples, the 3× CF4 plasma treatment did not significantly change the surface morphology or roughness. However, in the case of the T-LDPE samples, Scanning Electron Microscopy (SEM) images showed noticeable morphological changes, which were more significant at sharp edges of the surface structures.

Comparative study of plasma, laser, and flame induced activation of HDPE liner surfaces of type 4 hydrogen vessels

Enhanced Wetting and Adhesive Properties by Atmospheric Pressure Plasma Surface Treatment Methods and Investigation Processes on the Influencing Parameters on HIPS Polymer

Force-Based Characterization of the Wetting Properties of LDPE Surfaces Treated with CF4 and H2 Plasmas

Analysis of time-dependent hydrophobic recovery on plasma-treated superhydrophobic polypropylene using XPS and wettability measurements

Surface Treatment of HDPE Powders Using Inductively Coupled Plasma

Surface Modification and Adhesion Improvement of Expanded Poly(tetrafluoroethylene) Films by Plasma Graft Polymerization

Effects of Surface Modification by Argon Plasma on Peel Strength of Woven-Type Ultrahigh-Molecular-Weight Polyethylene

Mechanism of Hydrophobic Over-recovery on Polyethylene Surface Modified by Oxygen Plasma

Low-density polyethylene films treated by an atmospheric Ar--O2 post-discharge: functionalization, etching, degradation and partial recovery of the native wettability state

Modifying wetting properties of PI Film: The impact of surface texturing and CF 4 and O 2 plasma treatment

Adhesion studies of atmospheric pressure plasma-modified polyester fabrics with polyurethane coating

Study on Hydrophilicity of Polymer Surfaces Improved by Plasma Treatment

Surface Activation of Polylactic Acid-Based Wood-Plastic Composite by Atmospheric Pressure Plasma Treatment

Treatment of Polymeric Films Used for Printed Electronic Circuits Using Ambient Air DBD Non-Thermal Plasma

The Ageing of μPlasma-Modified Polymers: The Role of Hydrophilicity

Improvement of the Adhesion of High Density Polyethylene with Glass by Ar/O_2 Low-Temperature Plasma

Adhesive Properties of Polypropylene (PP) and Polyethylene Terephthalate (PET) Film Surfaces Treated by DC Glow Discharge Plasma

Morphologic and Chemical Properties of PMMA/ATH Layers with Enhanced Abrasion Resistance Realised by Cold Plasma Spraying at Atmospheric Pressure

Insight into the Effect of He Atmospheric Pressure Plasma Jets on Low-Density Polyethylene Surfaces by Fixed-Point Treatment

Improving film adhesive joining performance of poly(phenylene sulfide)/carbon fiber thermoplastic composite laminates by plasma surface treatment

Effects of Plasma Modification of Hybrid Kevlar/PTFE Fabric Surface on Adhesive and Tribological Properties