Abstract:In this research, we focused on the investigation of the structural, surface, and corrosion behavior properties of copper-loaded TiO2 nanotubular array surfaces that were further deposited with a chitosan biopolymer. This composite material was fabricated on Ti6Al4V alloy substrates using a combination of anodic oxidation (AO), electro-cathodic deposition (ECD), and electrophoretic deposition (EPD) techniques, primarily to apply it in medical implant contexts. Initially, the TiO2 nanotubes were prepared via anodization (AO). Subsequently, copper was introduced into the TiO2 nanotubes through electro-cathodic deposition (ECD), followed by the coating of chitosan over the copper-loaded TiO2 nanotubes using electrophoretic deposition (EPD). To comprehensively assess the characteristics of these surfaces, a series of analytical techniques were employed, including SEM, EDX mapping, XRD, and wettability measurements. Furthermore, the electrochemical properties of these surfaces, namely the OCP, PDP, and EIS, were extensively scrutinized. The outcomes of this investigation directed a notable development in the electrochemical corrosion resistance of the chitosan-deposited copper-loaded TiO2 nanotubular array surfaces in comparison to uncoated Ti6Al4V alloy, particularly under conditions simulating a physiological environment (simulated body fluid, SBF). Corrosion rates, assessed through PDP (Potentiodynamic Polarization) curves, were determined to be 0.3023 mm/y for polished Ti6Al4V, 0.1476 mm/y for TiO2 30 V 4 h, 0.1235 mm/y for TNT-Cu2/30/Ch, 0.0733 mm/y for TNT-Cu2/60/Ch, and 0.0611 mm/y for TNT-Cu2/90/Ch. Additionally, corrosion protection efficiencies were calculated as 51.16 % for TiO2 30 V 4 h, 59.15 % for TNT-Cu2/30/Ch, 75.76 % for TNT-Cu2/60/Ch, and 79.81 % for TNT-Cu2/90/Ch. Notably, the TNT-Cu2/90/Ch sample demonstrated a significantly low corrosion rate of 0.0611 mm/year and a high corrosion protection efficiency of 79.81 %. This enhancement can happen due to the chitosan coating, which acts as a protective layer, hindering the ingress of the physical solution into the original metal surfaces. Notably, TNT-Cu2/90/Ch coated sample exhibited a corrosion rate (icorr) approximately 5 times lower than that of the uncoated alloy. In conclusion, this study presents a novel chitosan-coated composite material consisting of copper-loaded TiO2 nanotubular surfaces that effectively enhances corrosion resistance compared to polished Ti6Al4V substrates.

Comparison of surface modification and corrosion resistance of Ti6Al4V alloy using matcha tea extract-based silver and copper oxide nanoparticles

Evaluation of surface properties of modified Ti6Al4V alloy with copper nanoparticles organic nanostructure for biomedical applications: dependency on anticorrosive, antibacterial, and biocompatibility

Green Synthesis of Ag and Cu Nanoparticles Using E. telmateia Ehrh Extract: Coating, Characterization, and Bioactivity on PEEK Polymer Substrates

The effect of silver nanoparticles on biological and corrosion behavior of electrophoretically deposited hydroxyapatite film on Ti6Al4V

Spray-deposited Ag nanoparticles on micro/nano structured Ti6Al4V surface for enhanced bactericidal property and cytocompatibility

Enhanced mechanical, bio-corrosion, and antibacterial properties of Ti Cu alloy by forming a gradient nanostructured surface layer

Structural and corrosion analysis of copper/chitosan coating on nanotubular TiO2/Ti6Al4V implant surface

Biological and antibacterial properties of chitosan-based coatings with AgNPs and CuNPs obtained on oxidized Ti13Zr13Nb titanium alloy

Antibacterial property and bioadaptability of Ti6Al4V alloy with a silvered gradient nanostructured surface layer

Development of bioactive and antimicrobial nano-topography over selective laser melted Ti6Al4V implant and its in-vitro corrosion behavior

Characterization and investigation of electrochemical and biological properties of antibacterial silver nanoparticle-deposited TiO2 nanotube array surfaces

The Optimization of the Synthesis of Antibacterial Coatings on Ti6Al4V Coupons Obtained by Electron Beam Melting

Antimicrobial Cu-Doped TiO2 Coatings on the β Ti-30Nb-5Mo Alloy by Micro-Arc Oxidation

Influence of Surface Modification of Titanium and Its Alloys for Medical Implants on Their Corrosion Behavior

Research on the surface characterization, corrosion and bioactivity of nano-featured tantalum coating on selective electron beam melted Ti6Al4V alloy

Enhanced in Vitro Biocompatibility of Ultrafine-Grained Biomedical NiTi Alloy with Microporous Surface

Silver Containing Antimicrobial Coatings on Innovative Ti-30Nb-5Mo β-Alloy Prepared by Micro-Arc Oxidation for Biomedical Implant Applications

Surface modification of Ti6Al4V alloy via advanced coatings: Mechanical, tribological, corrosion, wetting, and biocompatibility studies

Microstructure, Wettability, Corrosion Resistance and Antibacterial Property of Cu-MTa2O5 Multilayer Composite Coatings with Different Cu Incorporation Contents

Construction of a Rough Surface with Submicron Ti2Cu Particle on Ti-Cu Alloy and Its Effect on the Antibacterial Properties and Cell Biocompatibility

Ag nanoparticles incorporated tannic acid/nanoapatite composite coating on Ti implant surfaces for enhancement of antibacterial and antioxidant properties