Abstract:In magnetorheological polishing (MRP), the abrasive grains are confined in a semi-fixed mode by the chain strings formed by the magnetorheological particles to achieve the polishing of workpiece surfaces. The force of the abrasive particles on the workpiece comes from the force of the magnetic chain strings acting on the abrasives. However, the angular surface of the abrasive is generally smooth, resulting in a limited holding force on the abrasive by the magnetic chain strings. Therefore, the polishing force of the abrasives on the workpiece is small, and it is easy to slip and escape from the polishing area. In this paper, the sintering method is used to prepare polymerized diamond abrasive(PD) with microstructures on the surface, to increase the surface area of the abrasive and to improve the control force of the magnetic chain string on the abrasive. The prepared PD has a particle size of about 25.7 μm, with a rough surface and a large amount of 3 μm single-crystal diamond particles exposed. The MRP results show that the PD have more surface micro-cutting edges and stronger machinability than the commonly used single-crystal diamond abrasives(SCD). The material removal rate(MRR) of PD on silicon wafers and sapphire wafers was increased by 173.3 % and 122.2 %, respectively. The morphological changes of the PD were traced by scanning electron microscope(SEM), and it was found that: when polishing low-hardness materials, the wear of the PD was in the form of ceramic bond wear and diamond grit dislodgement; and when polishing high-hardness materials, the wear of the PD was in the form of ceramic bond breakage and PD fragmentation. When abrasive grit dislodgment occurs on the surface of the PD, the formed hole enhances the force between the PD and the magnetic chain strings. Which further enhances the holding force of the magnetic chain string on the PD, and can effectively improve the magnetorheological polishing efficiency.

Characteristics of magnetic elastic abrasive particles and their effect on tool passivation

Modelling and simulation of tool passivation by magnetic elastic abrasive particles

Magnetic Particle‐loaded Polymer Brushes Induced by External Magnetic Field: A Monte Carlo Simulation

Effect of abrasive particles on mechanical properties of magnetorheological elastomer

Research on Preparation and Properties of Magnetic Abrasive by Conventional Solid-State Method

Investigation of Synthesis, Characterization, and Finishing Applications of Spherical Al2O3 Magnetic Abrasives via Plasma Molten Metal Powder and Powder Jetting

Finishing mechanism modelling on magnetic abrasive finishing behaviours with core-shell magnetic abrasive particles

Material removal characteristics of magnetic-field enhanced shear thickening polishing technology

Preparation of Al2O3 magnetic abrasives by combining plasma molten metal powder with sprayed abrasive powder

Research on grinding force modelling of spherical alumina magnetic abrasive powder

Study on the rheological and polishing properties of electromagnetic two-phase composite particles with abrasive characteristics

Modeling and simulation of the action mechanism of multi-particles in magnetic abrasive finishing for internal blind cavity using the discrete element method

Optimizing processing performance of Fe-6.5 wt%Si–SiC magnetic abrasive particles by in-situ formation of Fe x Si y interlayer

Magnetization and self-sharpening mechanism of polymerized diamond abrasive based on magnetorheological polishing technology

Parametric Studies on Finishing of AZ31B Magnesium Alloy with Al2O3 Magnetic Abrasives Prepared by Combining Plasma Molten Metal Powder with Sprayed Abrasive Powder

Understanding of the Tribological Behaviors of Magnetic Lubrication Particle under Magnetic Field

Preparation and performance study of microporous magnetorheological elastomer polishing pad

Dynamic magnetic field magnetorheological finishing with constant load and variable gap

Enhanced machinability of aluminium-based silicon carbide by non-resonant vibration-assisted magnetorheological finishing

Behavior of the magnetic abrasive tool for cutting edge preparation of cemented carbide end mills

A Model for Mechanical Wear and Abrasive Particle Adhesion during the Chemical Mechanical Polishing Process