Abstract:This study presents a comprehensive investigation of fracture in open-stretched flanges formed using Single Point Incremental Forming (SPIF) on AA2024-T3 aluminium sheets. The work systematically explores the impact of geometric parameters, namely initial width and length, on the occurrence of the two primary failure modes: fracture at the corner and fracture at the edge of the flange. The experimental campaign comprises a series of flanging tests on medium-small radii to examine the deformation process on both the inner and outer surfaces of the flanges. The novelty of the investigation lies in two key aspects. Firstly, it offers, for the first time, an experimental characterisation of the onset of failure at the flange corner, which significantly limits the process's capabilities, and critically compares it with the failure at the flange edge. It is highlighted that the fracture at the corner is strongly influenced by tool-induced friction and the incremental nature of the SPIF process, resulting in a local formability significantly higher than expected with a quasi-proportional deformation process, as characterised by the conventional Fracture Forming Limit (FFL) evaluated through Nakazima tests. Secondly, a detailed formability analysis of the flange in the average stress triaxiality versus equivalent strain space is conducted, identifying a common region of Mode I fracture for plane stress applicable to both open-stretched flanges by SPIF and conventional Nakazima tests. To this end, an explicit numerical model based on the Barlat-89 anisotropic yield criterion is used to assess the non-proportional strain/stress paths, inherent in the incremental process. A numerical-experimental methodology is employed to predict both edge and corner failures of the flanges within the average stress triaxiality - equivalent strain space. The fracture loci for Mode I have been determined for both the incremental flanging tests and the Nakazima tests. A comparison of both fracture loci reveals a noticeably lower average stress triaxiality and larger equivalent strain in the SPIFed flanges than in the Nakazima tests, consistent with the increase in the apparent formability of the material observed experimentally in the incremental processes with respect to the conventional tests.

New Method for Detecting Flange Fracture Initiation in Incremental Radial Extrusion

Fracture in stretch flanging by single point incremental forming

Analysis of a New Process for Forming Two Flanges Simultaneously in a Hollow Part by Extrusion with Two Moving Dies

Theoretical and Experimental Study on the Effect of Selected Parameters in a New Method of Extrusion with a Movable Sleeve

Flange Forming at an Arbitrary Tube Location Through Upsetting with a Controllable Deformation Zone

Finite-element Modelling of a Novel Flanging Process on a Cylinder with a Large Diameter–thickness Ratio

AA5052 failure prediction of electromagnetic flanging process using a combined fracture model

Formation criterion of fissure defects in the inner wall of the radial forged steel tube

Axial Hydro-Forging Sequence for Variable-Diameter Tube of 6063 Aluminum Alloy

Experimental and numerical investigations into the ductile fracture during the forming of flat-rolled 5083-O aluminum alloy sheet

Prediction and Analysis of Breakthrough Extruding Force Based on a Modified FE-model in Large-Scale Extrusion Process

A new tube forging process for manufacturing hollow parts with inner flange at an arbitrary location

Investigations on Failure-to-fracture Mechanism and Prediction of Forming Limit for Aluminum Alloy Incremental Forming Process

An Analytical Model of Material Deformation During Friction Welding of Alloy 718

Process Parameter Optimization in Refill Friction Spot Welding of 6061 Aluminum Alloys Using Response Surface Methodology

Alternative Approach to Model Ductile Fracture by Incorporating Anisotropic Yield Function

A direct analytical methodology for the assessment of ductile fracture in metals based on multiaxial tests

Axial Rotary Forging of Inner Flanges at Thin Wall Tube Blanks

Investigation of Thickness Variation in Axial Hydro-Forging Sequence for Variable-Diameter Tubes

A New Method to Calculate Threshold Values of Ductile Fracture Criteria for Advanced High-Strength Sheet Blanking

Application of an Incremental Constitutive Model for the FE Analysis of Material Dynamic Restoration in the Rotary Tube Piercing Process