Abstract:Deformation processing is a commonly used strategy to improve the microstructure and hence mechanical properties of biodegradable Zn alloys. However, a single conventional processing method is usually limited in achieving this goal. In this work, hot extrusion combined with room-temperature equal channel angular pressing (ECAP) was used to fabricate biodegradable Zn–Cu–Li alloy. Compared to the hot-extruded alloy, the further ECAPed alloys have significantly finer Zn grains and precipitate more submicron- and nano-sized ε -CuZn 4 particles. Moreover, the 4-pass as-ECAPed alloy exhibits the best comprehensive mechanical properties with yield strength of 315 ± 3 MPa, ultimate tensile strength of 444 ± 13 MPa and elongation of 81 ± 5%, which are 13.3%, 38.8% and 72.3% higher than those of the hot-extruded alloy, respectively. In addition, in vitro and in vivo tests were performed on the 4-pass as-ECAPed alloy to evaluate its corrosion behavior, antibacterial property, cytotoxicity and biocompatibility. In vitro results showed that the 4-pass as-ECAPed alloy exhibits better corrosion resistance than the 8-pass alloy. Also, it shows good antibacterial property, hemocompatibility and cytocompatibility. In vivo results demonstrated that the 4-pass as-ECAPed alloy exhibits faster and more uniform degradation than the pure Zn (as a control group). Both the pure Zn and 4-pass as-ECAPed alloy promote formation of new bone, the mass of which increases over time. The 4-pass as-ECAPed alloy shows slightly weaker osteogenic capacity but better overall osteointegration than the pure Zn. Furthermore, both the pure Zn and 4-pass as-ECAPed alloy exhibit good in vivo biosafety.

Effect of grain size on the mechanical properties of Fe-30Mn-6Si biodegradable alloy

In Vitro Investigation of Fe30Mn6Si Shape Memory Alloy As Potential Biodegradable Metallic Material

Enhanced Mechanical Performance of a Biodegradable Fe-Mn Alloy Manufactured by Metal Injection Molding and Minor Carbon Addition

Microstructure, Mechanical Properties, and in Vitro Corrosion Behavior of Biodegradable Zn-1Fe-xMg Alloy

Tailoring grain sizes of the biodegradable iron-based alloys by pre-additive manufacturing microalloying

Effects of metalloid Si on the microstructure and mechanical properties of Fe36Ni36Cr10Mo1Al17-XSiX alloys

Effects of Si addition on mechanical, electrical and magnetic property of Cu-10Fe alloy

Effect of original grain size on microstructure and properties of extruded Mg-2Zn-0.2Mn biomedical alloy

Fe-bearing phase formation, microstructure evolution, and mechanical properties of Al-Mg-Si-Fe alloy fabricated by the twin-roll casting process

Effect of Fe and Mn Content on the Microstructures and Tensile Behaviour of AlSi7Cu3 Alloy: Thermal Analysis and Tensile Tests

Grain size evolution and mechanical properties of thermomechanically processed pure iron for biodegradable medical implant application

An in vitro and in vivo study of biodegradable Zn–Cu–Li alloy with high strength and ductility fabricated by hot extrusion combined with room-temperature ECAP

Enhanced mechanical properties and microstructural stability of ultrafine-grained biodegradable Zn-Li-Mn-Mg-Cu alloys produced by rapid solidification and high-pressure torsion

Effects of alloying elements (Ca and Sr) on microstructure, mechanical property and in vitro corrosion behavior of biodegradable Zn-1.5Mg alloy

Effects of Li addition on the properties of biodegradable Zn–Fe–Li alloy: Microstructure, mechanical properties, corrosion behavior, and cytocompatibility

Mechanical Properties of Biomedical Ultrafine Grained Mg-3Sn-0.5Mn Alloy Processed by Equal-Channel Angular Pressing

A bimodal grain structured Zn–0.5Ag–0.2Mg alloy with high strength and ductility achieved through combined ECAP and cold rolling

Effect of Initial Fe Content on Microstructure and Mechanical Properties of Recycled Al-7.0Si-Fe-Mn Alloys with Constant Mn/Fe Ratio

Effect of Si on Fe-rich intermetallic formation and mechanical properties of heattreated Al-Cu-Mn-Fe alloys

Effect of ultrasonic melt processing and cooling rate on microstructure evolution of Al–Cu–Mn–Mg–Fe–Si alloy

Effects of grain size on the precipitation pathway and mechanical properties of (CoCrFeNi)94Ti2Al4 high entropy alloy