Abstract:Power conversion efficiency (PCE) of organic solar cells (OSCs) has reached the threshold for application. However, the high PCEs are mostly obtained from the small‐area OSCs processed by the halogenated solvent, such as chloroform (CF), because the high‐performance A‐DA'D‐A type small molecule acceptors (SMAs) need the CF processing for suitable solubility and rapid solvent evaporation to get appropriate aggregation morphology. Herein, we synthesized two new A‐DA'D‐A type SMAs of Y6‐Ph and L8‐Ph by introducing a phenyl end group in the branched alkyl inner side chains of the representative SMAs Y6 and L8‐BO respectively, for overcoming the excessive aggregation of SMAs in the long‐time film‐forming process in the nonhalogenated solvent processing. Firstly, we studied the effect of the processing solvent boiling point on the aggregation property and photovoltaic performance of the four SMAs of Y6, L8‐BO, Y6‐Ph and L8‐Ph, by using the most commonly used halogenated processing solvents: low‐boiling‐point CF (rapid film forming process) and high‐boiling‐point chlorobenzene (CB) (slow film forming process) for device fabrication of the OSCs with PM6 as polymer donor. It was found that the Y6‐ and L8‐BO‐based OSCs exhibit a dramatic drop in PCEs from CF‐ to CB‐processed devices owing to the large phase separation in the CB‐processed OSCs. On the contrary, the devices based on Y6‐Ph and L8‐Ph with the phenyl ending inner side chains show obviously increased PCEs for the OSCs processed by high‐boiling‐point CB. The L8‐Ph‐based devices processed by CB demonstrated an PCE of 18.83% with a high FF of 80.55%, which is even better than the L8‐BO‐based OSCs processed by CF. Furthermore, the L8‐Ph‐based OSCs processed by nonhalogenated solvent o‐xylene (o‐XY) also achieved a high PCE of 18.40% with an FF of 80.11%, which is the best‐performed OSC fabricated from the nonhalogenated solvents so far. In addition, the large‐area (1 cm2) OSCs based on PM6:L8‐Ph processed by o‐XY also demonstrated a higher PCE of 16.66%. The results indicate that introducing phenyl end group in the inner side chains is an effective strategy to improve photovoltaic performance of the A‐DA'D‐A SMAs for future application of the OSCs with nonhalogenated solvent processing. This article is protected by copyright. All rights reserved

Fluorination or Not in Small Molecule Solar Cells: Achieving a Higher Efficiency with Halogen‐free End Group

To Fluorinate or Not to Fluorinate in Organic Solar Cells: Achieving a Higher PCE of 15.2% when the Donor Polymer is Halogen‐Free

Efficient small‐molecule organic solar cells by modulating fluorine substitution position of donor material

End-group modification of non-fullerene acceptors enables efficient organic solar cells

Over 19% Efficiency Organic Solar cells Enabled by Manipulating the Intermolecular Interactions through Side Chain Fluorine Functionalization

Fluorinated End Group Enables High‐Performance All‐Polymer Solar Cells with Near‐Infrared Absorption and Enhanced Device Efficiency over 14%

Synergistic direct and indirect central unit fluoridation of non-fullerene acceptor enables high-efficiency organic solar cells

Asymmetric Acceptors with Fluorine and Chlorine Substitution for Organic Solar Cells toward 16.83% Efficiency

Systematically Controlling Acceptor Fluorination Optimizes Hierarchical Morphology, Vertical Phase Separation, and Efficiency in Non‐Fullerene Organic Solar Cells

Synergistic Effects of Side‐Chain Engineering and Fluorination on Small Molecule Acceptors to Simultaneously Broaden Spectral Response and Minimize Voltage Loss for 13.8% Efficiency Organic Solar Cells

Selective halogenation of central and end-units of nonfullerene acceptors enables enhanced molecular packing and photovoltaic performance

High-efficiency Organic Solar Cells Processed from a Halogen-Free Solvent System

Synergistic Effect of Fluorination on Both Donor and Acceptor Materials for High Performance Non-Fullerene Polymer Solar Cells with 13.5% Efficiency

Fluorination of Terminal Groups Promoting Electron Transfer in Small Molecular Acceptors of Bulk Heterojunction Films

A Difluoro‐Monobromo End Group Enables High‐Performance Polymer Acceptor and Efficient All‐Polymer Solar Cells Processable with Green Solvent under Ambient Condition

Achieving Balanced Charge Transport and Favorable Blend Morphology in Non-Fullerene Solar Cells Via Acceptor End Group Modification

Halogenation Strategy of Thiophene Derived Solvent Additives Enables Optimized Morphology for Organic Solar Cells with 19.17% Efficiency

Rebuilding Peripheral F, Cl, Br Footprints on Acceptors Enables Binary Organic Photovoltaic Efficiency Exceeding 19.7%

Linker Group Fluorination Boosts Photovoltaic Performance of Branch‐Connected Dimerized Acceptors

Introducing Phenyl End Group in The Inner Side Chains of A‐Da'd‐A Acceptors Enables High‐Efficiency Organic Solar Cells Processed with Nonhalogenated Solvent

Comprehensive Understanding of Fluorination-Performance Relationship: The Best-Performed A-D-A-Type Acceptors