Abstract:This research focused on the investigation of the metallurgical behavior of the Al0.8CoCrFeNi high-entropy alloy and S235JR structural steel, welded with (Ni, Fe)-rich filler metal, by the Gas Tungsten Arc Welding (GTAW) method. The electric arc and the welding pool were protected against the contamination with gases from the environment, by employing high-purity Ar 4.8 inert gas that plays an important role in reducing the oxidation effects and the development of cracks in the weld and the adjacent areas. The microstructure and microhardness analysis did not reveal the existence of fragile phases, cracks, inadequate penetration, or other imperfections, showing an appropriate adhesion between the deposited metal and the substrates. At the interface between the Ni-rich weld metal and the high-entropy alloy, a higher hardness (448 HV0.2) than in the base material (358 HV0.2) was measured. Energy-dispersive X-ray analysis (EDS), performed at the interface between the weld metal and the base materials, did not show significant modifications of Co, Fe, and Cr percentages. However, during the investigation, significant variations in Al and Ni concentrations were observed, caused by the fast diffusion of chemical elements, and the development of hard (Ni, Al)-rich compounds. In some areas of the deposited metal, located at a distance of about 10 μm from the interface, the percentages of Ni and Al were higher than in the high-entropy alloy base material, being around 41% by weight Ni and over 13% by weight Al, while the concentrations of the Co, Cr, and Fe elements proportionally decreased (i.e., approximately 14% by weight Co, 12% by weight Cr, and 17% by weight Fe). The development of Ni3Al and NiAl compounds was also noticed, whose formation was determined by the local chemical concentration and the temperature reached in the vicinity of the diffusion zone. The XRD analysis showed a group of X-ray peaks in the Al0.8CrFeCoNi alloy that corresponded to both α-type—BCC and FCC phases. The crystallite size of the high-entropy alloy investigated was found to be 22.05 nm. Despite the diffusion phenomenon, if filler materials and process parameters are appropriately selected, quality joints of high-entropy alloys and structural steels can be carried out under good welding conditions.

Effect of Gibbs Free Energies of Terminal Alloys on the Diffusion Paths and Diffusion Depths in Couples Assembled with γ-Phase Fe-Ni-Cu Alloys at 1000 °C

Effect of Substrate Characteristics on Interdiffusion Coefficients of Ni and Al Atoms in Β-Nial Phase of Aluminide Coatings

An Experimental Estimation Method of Diffusion Coefficients in Ternary and Multicomponent Systems from a Single Diffusion Couple Profile

Characterization of Ductile Nano-Tic Dispersed V4Cr4Ti/RAFMs Solid Diffusion Joint for Nuclear Fusion Reactor Application

Interdiffusion Studies in Alloy 617 and 10Cr Steel Joints Using Diffusion Couple Approach and Simulations

An experimental estimation method of diffusion coefficients in ternary and multicomponent systems from a single diffusion profile

Interdiffusion in the FCC-structured Al-Co-Cr-Fe-Ni High Entropy Alloys: Experimental Studies and Numerical Simulations

Solving the issues of multicomponent diffusion in an equiatomic NiCoFeCr medium entropy alloy

Interfacial Reactions in the Liquid Diffusion Couples of Mg/Ni, Al/Ni and Al/(Ni)-Al2O3 Systems

Interfacial behaviour of the high-entropy alloy CuCoCrFeNi and TC4 joint obtained by vacuum diffusion welding

High Entropy and Sluggish Diffusion "Core" Effects in Senary FCC Al-Co-Cr-Fe-Ni-Mn Alloys

Effects of temperature gradient on the interface microstructure and diffusion of diffusion couples: phase-field simulation

High-throughput pseudo-binary diffusion couple approach for alloy design in cobalt-based superalloys

Thermodynamic assessment of the Co–Fe–Ni system and diffusion study of its fcc phase

Interdiffusion and atomic mobility in FCC Ag–Cu–Ni alloys

Influence of compositional complexity on interdiffusion in Ni-containing concentrated solid-solution alloys

[P77] Thermodynamic Description, Diffusivities and Atomic Mobilities in Binary Ni–Os Alloys

Composition dependence of tracer diffusion coefficients in Fe-Ga alloys: a case study by a tracer-interdiffusion couple method

Development of different methods and their efficiencies for the estimation of diffusion coefficients following the diffusion couple technique

Automated Development of an Accurate Diffusion Database in Fcc AlCoCrFeNi High-Entropy Alloys from a Big Dataset of Composition Profiles

Effect of Diffusion on Dissimilar Welded Joint between Al0.8CoCrFeNi High-Entropy Alloy and S235JR Structural Steel