Abstract:Purpose: To investigate the early postoperative gait characteristics of patients who underwent periacetabular osteotomy (PAO) and predict the biomechanical performance of two commonly used PAO fixation methods: iliac screw (IS) and transverse screw (TS). Methods: A total of 12 patients with unilateral developmental dysplasia of the hip (DDH) (mean age 27.81 ± 4.64 years, 42% male) that were scheduled to undergo PAO surgery were included in this study. Their preoperative CT images and pre- and postoperative gait data were used to create subject-specific musculoskeletal models and complete the inverse dynamics analysis (IDA). Two patients with typical gait characteristics were selected using clustering analysis, and their IDA data were incorporated into finite element (FE) models of IS and TS fixations. Failure simulation was performed by applying iterative steps with increasing gait load to predict yield load. Stress results and yield loads were calculated for each FE model at different phases of the gait cycle. Results: Postoperative gait showed improvement compared to preoperative gait but remained inferior to that of healthy individuals. Postoperative gait was characterized by a lower hip range of motion, lower peri-ilium muscle forces, particularly in the abductors, and a sharper initial peak and flatter second peak of hip joint reaction force (HRF). Finite element analysis (FEA) showed a trend of increasing stress during the second–fourth phases of the gait cycle, with lower stress levels in other phases. At high-stress gait phases, the mean stress of maximum p ̄100 differed significantly between IS and TS ( p < 0.05) and between coupled and uncoupled muscle forces ( p < 0.05). Failure analysis predicted a slightly larger yield load for TS configurations (6.21*BW) than that for IS (6.16*BW), but both were well above the gait load. Coupled and uncoupled groups showed similar results, but uncoupled groups had lower yield loads (5.9*BW). Conclusion: PAO early postoperative gait shows a normalized trend, but abnormalities persist. IS and TS are both capable of resisting mechanical strain failure, with no significant mechanical advantage found for transverse screw fixation during PAO early postoperative gait. Additionally, it is important to note that the TS may have a higher risk of cyclic fatigue failure due to the localized greater stress concentration. Furthermore, the most medial screw is crucial for pelvic stability.

Biomechanical analysis of load distribution in porcine hip joints at different acetabular coverages

Biomechanical changes in the lumbar and hip joint after curved periacetabular osteotomy

A Computer Modeling-Based Target Zone for Transposition Osteotomy of the Acetabulum in Patients with Hip Dysplasia

What Are the Sex-Based Differences of Acetabular Coverage Features in Hip Dysplasia?

Analysis of Finite Element Modeling on Elasto-Plasticity of Polyethylene Liner under Contact Stress after THA

Effects of rotational acetabular osteotomy on the mechanical stress within the hip joint in patients with developmental dysplasia of the hip: a subject-specific finite element analysis.

Hemiarthroplasty of hip joint: An experimental validation using porcine acetabulum

Incorporating patient-specific hip orientation from weightbearing computed tomography affects discrete element analysis-computed regional joint contact mechanics in individuals treated with periacetabular osteotomy for hip dysplasia

Biomechanical Research on Contour Cage with Transacetabular Screws Fixation in Revision Total Hip Arthroplasty.

Mechanical upside of PAO mainstream fixations: co-simulation based on early postoperative gait characteristics of DDH patients

Extended mechanical loads for the analysis of acetabular cages

Biomechanical analysis and clinical observation of 3D-printed acetabular prosthesis for the acetabular reconstruction of total hip arthroplasty in Crowe III hip dysplasia

Analysis of contact pressure in a 3D model of dual-mobility hip joint prosthesis under a gait cycle

A histological study of articular cartilage after rotational acetabular osteotomy for hip dysplasia

Finite Element Analysis of Various Osteotomies Used in the Treatment of Developmental Hip Dysplasia in Children

Relationship between spinal sagittal alignment and acetabular coverage: a patient-matched control study

Role of the Anterior Center-Edge Angle on Acetabular Stress Distribution in Borderline Development Dysplastic of Hip Determined by Finite Element Analysis

A novel classification to guide total hip arthroplasty for adult acetabular dysplasia

Hip joint contact pressure and force: a scoping review of in vivo and cadaver studies

Effect of Bone Coverage on Acetabular Implant Stresses in Standard and Dual-Mobility Total Hip Arthroplasty Constructs: A Finite Element Model

Combined assessment of acetabular coverage and femoral head-neck shapes predicts osteoarthritis progression after periacetabular osteotomy