Abstract:In recent years numerical simulation has become one of the most important means to study the complex oil flow within gearbox. Since the gap between tooth surfaces near the gear mesh zone is quite tiny, it’s difficult to get high quality mesh grid near such zone. Further numerical divergence frequently occurs along iterative process with dynamic mesh. To overcome this predicament, some researchers have tried different gear modeling methods to simplify the gear model, such as none-teeth method, cutting-teeth method or gear-separation method. Nevertheless these methods have certain limitation. This paper attended to provide a new practical gear modeling methods called teeth-face-moving method. The method was operated by moving each tooth surface slightly. As the tooth thickness was marginally reduced, the gap between tooth surfaces near the mesh zone was increased to 0.5-1 mm, so that mesh generation in the gap became feasible, which was different from the previous methods, i.e. all of teeth profiles and the center distance of 2 gears were kept as same as the original when using the teeth-face-moving method. To certify the reasonability of this new method, a numerical model for splash lubrication in gearbox was built with different gear modeling methods. The volume of fluid (VOF) method was applied to track the air and oil two-phase flow. And RNG k-ε model was introduced to describe turbulence flow considering high fluid strain rate and high bending degree of flow line. Standard wall function was applied to deal with the flow near wall region and low Reynolds number flow. Dynamic mesh method with the spring-based smoothing and local remeshing was used to adapt the motion of gears. Due to more concentrating upon mesh zone, the gear-separation method and the teeth-face-moving method required more grid elements and computational resource than other methods. The numerical results of oil distribution and gears’ churning loss were comparatively analyzed. Also the simulated results were made a comparison with the existed experiment data. It was easily observed the quantity of oil splashed by gears with none-teeth method or cutting-teeth methods was obviously less than that with gear-separation method or teeth-face-moving method. The similar phenomenon was acquired from churning loss results as well. The churning loss computed with none-teeth method or cutting-teeth method was far less than the related experimental result. On the contrary the churning loss computed with gear-separation method or teeth-face-moving method showed good agreement with the related experimental result. The direct reason was tip diameter and teeth profile had a strong influence on the oil flow in the gearbox. So cutting all or partial teeth may lead unreliable simulation result for splash oil flow. It seemed that the gear-separation method got the result close to the teeth-face-moving method. Unfortunately the center distance of 2 gears had to be increased for the gear-separation method. This was unacceptable in real engineering case because changing the position of gear may lead to related bearings or shaft intersected with other structures, such as bearing base and gearbox housing. So the conclusion is drawn that the teeth-face-moving method not only provides more credible prediction for oil flow in the gearbox, but also has more practicability for complicated engineering situation and hence is superior to the previous gear modeling methods. The teeth-face-moving gear modeling method is quite beneficial to lubrication simulation for real engineering gear system, such as truck axle or vehicle transmission. And further work of applying this new method on complicated machinery is underway.

Injection lubrication for high-speed helical gears using the overset mesh method and experimental verification

Study on oil film spreading characteristics on the jet lubricating tooth surface of aviation herringbone gear

Investigations of the Micro Surface Shape for the Gear-Shaft/journal-bearing Interface in Water Hydraulic Internal Gear Pumps

Simulation Analysis for Lubrication State of the Thrust Washer Within Straight Planetary Gear Set

Mathematical modeling and numerical simulation for determining an optimized oil jet layout for spiral bevel gear lubrication

Study on Heat Transfer Characteristics of High-Speed Herringbone Gear in Meshing Process Under Oil Injection Lubrication

Determination of an Optimal Oil Jet Nozzle Layout for Helical Gear Lubrication: Mathematical Modeling, Numerical Simulation, and Experimental Validation

Gear splash lubrication numerical simulation and validation based on teeth-face-moving method

Modeling and analysis of transient lubrication characteristic of the helicopter main transmission spiral bevel gears in point contacts

Numerical and Experimental Investigation of Splashing Oil Flow in a Hypoid Gearbox

Lubrication mechanism in gearbox of high-speed railway trains

Lubrication Performance of Helical Gear Pair Under Dynamic Load Based on Local Involute Profile

Experimental and Numerical Study of the Influence of Loading Direction on the Lubrication and Cooling of Self-Circulating Oil Bearing System Applied in Internal Gear Pumps

Hydrostatic bearing groove multi-objective optimization of the gear ring housing interface in a straight-line conjugate internal meshing gear pump

Dynamic Evolution Characteristics of the Gear Meshing Lubrication for Vehicle Transmission System

Lubrication characteristic of tooth surface on arc tooth cylindrical gears

Predicting Film Parameter and Friction Coefficient for Helical Gears Considering Surface Roughness and Load Variation

Simulation and experiment on vibration of helical gear transmission considering EHD

Investigation of the Lubrication System in a Vehicle Axle: Numerical Model and Experimental Validation

Experimental Research on Reasonable Lubricant Quantity for Transmission Gears Used in High-Speed Train

Study on the influence of key design parameters on lubrication characteristics of a novel gear system applying Taguchi method