Abstract:As we know, 3DPC is printed layer by layer compared with mold-casting conventional concrete. Pore structure and layer-to-layer interface are two main aspects of the internal structure for 3DPC, which decide 3DPC's mechanical performance. The layer-to-layer interface caused by printing is specific to 3DPC. The emphasis of this study lies in the layer-to-layer interfaces of 3DPC. The first aim of this study is to quantify the characteristics of the layer-to-layer interface and therefore characterize different aspects of the interfaces. The second aim of this study is to explore how the internal structure of printed concrete influences the mechanical performance of 3DPC. This research set out to design a series of experimental comparisons between 3DPC and casted concrete with the same compositions. Mechanical tests, i.e., compressive stress, ultrasonic Pulse Velocity test, flexural tension, and tension splitting, as well as the Ultrasonic Pulse Velocity test, were performed to check the mechanical performance of 3DPC. Contrary to what has often been expected, the mechanical test results showed the printed concrete has a quality not worse than casted concrete with the same recipe. Meanwhile, the X-ray computed tomography (X-CT) is used to characterize the internal structure, pore shapes, and interfaces of 3DPC. First, the investigation revealed that the lower total porosity and fewer big voids could be the fundamental causes meaning 3DPC has a better mechanical performance than casted concrete. Second, the statistics based on aspect ratio show that the distribution curves follow similar trends, regardless of the printed or casted concrete. Third, this study quantified the depth of the different interfaces for 3DPC. The results suggest that the porosity in an interface varies in a range. The author's pioneer work has contributed to our present understanding of the interfaces of 3DPC.

Rheological and Mechanical Properties of Polyformaldehyde Fiber Reinforced 3D-Printed High-Strength Concrete with the Addition of Fly Ash

Investigation of the Internal Structure of Hardened 3D-Printed Concrete by X-CT Scanning and Its Influence on the Mechanical Performance.

Modification effect of nanosilica and polypropylene fiber for extrusion-based 3D printing concrete: Printability and mechanical anisotropy

Experimental Study on the Flexural Fatigue Performance of Slag/fly Ash Geopolymer Concrete Reinforced with Modified Basalt and PVA Hybrid Fibers

Study on anisotropy of 3D printing PVA fiber reinforced concrete using destructive and non-destructive testing methods

Triaxial compressive behavior of 3D printed PE fiber-reinforced ultra-high performance concrete

PVA Fibre Reinforced High-Strength Cementitious Composite for 3D Printing: Mechanical Properties and Durability

Optimization of Foams—Polypropylene Fiber-Reinforced Concrete Mixtures Dedicated for 3D Printing

Rheological behaviors and structure build-up of 3D printed polypropylene and polyvinyl alcohol fiber-reinforced calcium sulphoaluminate cement composites

Mechanical Properties and Microstructure of Highly Flowable Geopolymer Composites with Low-Content Polyvinyl Alcohol Fiber

Rheological characterization of ultra-high performance concrete for 3D printing

Investigation of fresh and hardened properties of 3D printable concrete containing ozone-modified carbon fiber

Influence of hydroxypropyl methylcellulose and silica fume on stability, rheological properties, and printability of 3D printing foam concrete

Flexural fatigue performance and damage evolution analysis of multiscale polypropylene fiber‐reinforced concrete

Thermally stimulated stiffening and fly ash's alkaline activation by Ca(OH) 2 addition facilitates 3D-printing

Study of 3D printed concrete with low-carbon cementitious materials based on its rheological properties and mechanical performances

Experimental investigations on tensile strength and fracture toughness of a polyoxymethylene fiber reinforced concrete

Enhancing Mechanical Properties of Three-Dimensional Concrete at Elevated Temperatures through Recycled Ceramic Powder Treatment Methods

3D-printing ultra-high performance fiber-reinforced concrete under triaxial confining loads

Utilization of antimony tailings in fiber-reinforced 3D printed concrete: A sustainable approach for construction materials

Shrinkage and Cracking Properties of Cellulose Fiber–Concrete Composites for 3D Printing by Leveraging Internal Curing