Abstract:Purpose This study aims to form composite solid lubricant coatings on the surface of bearing steel, which can significantly improve the tribological properties of thrust cylindrical roller bearings (TCRBs). Phosphating films possess microscopic porosity that typically needs to be sealed with oil, grease or wax. Due to its unique crystal structure, the phosphating film itself also exhibits a certain degree of lubricity. In this study, solid lubricants are used to fill the pores of the phosphating film. By combining the phosphating film with solid lubricants, lubrication and wear reduction can be achieved. Design/methodology/approach In this study, the surfaces of the shaft washer (WS) and seat washer (GS) were treated with zinc-phosphating. Subsequently, a solid lubricant solution (polytetrafluoroethylene [PTFE], MoS 2 and graphite) was sprayed onto the phosphated samples at concentrations of 1 , 2 and 3 g/L. The porous and adsorptive nature of the phosphating film was used to embed the solid lubricant particles into the film, thus forming a composite lubrication layer containing solid lubricants on the surface of the bearing steel. Findings The addition of solid lubricant materials has shown significant potential in reducing wear losses compared with phosphated samples without such additives. Increasing the amount of solid lubricant added can facilitate the formation of a transfer film, which further enhances the protective properties. However, it is important to note that excessive amounts of solid lubricant material can contribute to seizure, leading to increased wear losses of the cage and a higher average coefficient of friction (ACOF).By spraying a PTFE solution with a concentration of 2 g/L, the lowest ACOF and cage wear loss were achieved, resulting in reductions of 60.5% for the ACOF and 89.4% for the cage wear loss. Similarly, when spraying a graphite solution with a concentration of 3 g/L, the lowest wear losses for GS and WS were observed, with reductions of 51.7% for GS wear loss and 38.9% for WS wear loss. Originality/value The combination of the phosphating film and solid lubricants aims to achieve lubrication and wear reduction, providing a new approach to wear-resistant technology for TCRBs. Peer review The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-07-2023-0231/

Reliability Study of Solid-Liquid Coupled Lubrication Coatings for Fasteners

Universal and Stable Slippery Coatings: Chemical Combination Induced Adhesive-Lubricant Cooperation

Tribological properties and corrosion resistance of epoxy resin‐polytetrafluoroethylene bonded solid lubricating coating filled with flake aluminum

Friction and Wear Behavior of PTFE Coatings Modified with Poly (methyl Methacrylate)

Preparation and frictional characteristics of solid lubrication coating on CFRP surface

Combining Carbon Nanoparticle Coatings and Laser Surface Texturing for Enhanced Lubricity Under High Loads

Significant Enhancement of Tribological Properties of Microcapsule/epoxy Composites in the Presence of High Loads by Incorporating PTFE

Tribological Behavior of Reinforced PTFE Composites and Un-Reinforced Polyketone-Based Materials against Coated Steel

Ultralow Friction Polymer Composites Enabled by the Solid–liquid Core Microcapsules at High Temperatures

Flake aluminum reinforced polyamideimide-polytetrafluoroethylene bonded solid lubricating composite coating for wear resistance and corrosion protection

Preparation and tribological properties of solid-liquid synergetic self-lubricating PTFE/SiO2/PAO6 composites

Friction and Wear Behavior of Polytetrafluoroethylene Bond- ed Solid Lubricating Coaling under Oil Lubrication

Sweating-like engineered ultra-low friction coating by a template assisted method

Investigation of the Mechanisms for Stable Superlubricity of Poly(vinylphosphonic Acid) (PVPA) Coatings Affected by Lubricant

The Effects of PTFE Content on Microstructures and Properties of Composite Brushing Plating Coating

Encapsulated Liquid Lubricants Incorporated in Metal Matrix Thermal Spraying Coatings

Organic-ceramic hybrid lubricating coating from thermal-sprayed ceramic templates

Effects Of Polymer Composited Lubricant Coating On Tribological Properties Of Low-Carbon Steel Surface

Effect of composite solid lubricant coatings on the tribological performance of thrust cylindrical roller bearings

Dual-Function Hybrid Coatings Based on Polytetrafluoroethylene and Cu2O for Anti-Biocorrosion and Anti-Wear Applications

Analysis of the lubrication process with composition of solid lubricants of laser-modified sliding surfaces