Abstract:Conventionally assembled monolithic concrete frame structures achieve structural ductility through beam-end failure, which results in structures that are difficult to repair after an earthquake. To improve the seismic and resilience performance, a prefabricated concrete beam–column joint with replaceable graded-yielding energy-dissipating connectors (RGECs) is introduced. The connectors assembled on the upper and lower sides of the beam end dissipate energy and transfer the beam-end load with the steel hinge device. By adjusting the design bearing-capacity coefficient of RGECs to precast beams, the plasticity and damage of the structure can be centered on the core energy-dissipation bending–shear components (BSCs) and buckling segment (BS) of the RGEC, and the structural function can be quickly recovered by replacing only the damaged RGECs after a seismic disaster. Moreover, compared to the conventional joints, the joint with RGEC can achieve target seismic-performance goals at different seismic-risk levels by designing BSCs and BS with graded yielding. Low-cyclic-loading tests were performed on seven full-scale beam–column joint specimens to investigate the effects of different core energy-dissipating member thicknesses, beam reinforcement ratios and loading protocols on the seismic behavior of the proposed joint. Subsequently, the damaged RGECs were replaced, and the structural-function resilience performance was evaluated in terms of the function-recovery efficiency and quality, indicated by the hysteresis response, strain development, and component energy dissipation. The experimental results proved that the beam–column joint exhibited excellent seismic performance and could realize graded-yielding energy dissipation. The damage to the specimens was concentrated in the RGECs, the key members (beams and columns) were in an elastic state, and the energy dissipation ratio of the RGEC was more than 97 %. This enables the rapid recovery of function after earthquakes. After replacing the RGEC, the hysteresis response, strain development, and component energy dissipation of the specimens were consistent with those of the initial specimens. Compared with the original specimen, the difference in each seismic index of the replaced specimen was less than 10 %. Additionally, the structural function recovered quickly, and the resilient performance was good.

Experimental Research on the Seismic and Repair Performance of Steel Beam-Column Joint with Replaceable Bio-Inspired Hinge

Experimental Research on Seismic Behavior of Reinforced Concrete Column-to-Steel Beam Joints with Bolted End-plate

EXPERIMENTAL STUDY ON THE SEISMIC BEHAVIOR OF CFST RECTANGULAR COLUMN TO H-SECTION STEEL BEAM CONNECTIONS WITH EXTERNAL STIFFENERS

Experimental Study on Reduced I-beam to CFRST Column Joints under Cyclic Loading

Research on the Seismic Performance of Precast Concrete Columns with Replaceable Bionic Hinge Connections

Seismic performance of prefabricated beam-to-column joint with replaceable energy-dissipating steel hinge

Experimental study on low-damage performance of Sliding Hinge Joint

Experimental study on a single-sided resilient composite beam–column joint

Seismic behavior of a replaceable artificial controllable plastic hinge for precast concrete beam-column joint

Seismic behavior and resilience assessment of prefabricated beam–column joint with replaceable graded-yielding energy-dissipating connectors

An RBS-based replaceable precast concrete beam-column joint: Design approach and experimental investigation

Experimental study on the seismic behavior of an innovative stepped beam-column joint

Experimental Study on a Damage-Control and Repairable Fully Precast Beam-Column Joint

Research on design and numerical simulation of self-centering prefabricated RC beam-column joint with pre-pressed disc spring devices

Experimental Research on Seismic Performance of a New-Type of R/C Beam-Column Joints with End Plates

Experiment on seismic behavior of earthquake-resilience prefabricated cross hinge column foot joint

Static and Seismic Experimental Study of Novel Prefabricated Beam-Column Joints with Elongated-Hole Brackets

Deformation Mechanism Analysis of Steel Artificial Controllable Plastic Hinge in Prefabricate Frame

Seismic performance of self-centering beam-column joints reinforced with superelastic shape memory alloy bars and engineering cementitious composites materials

Numerical study of the seismic performance of a double-hinge steel frame joint

Development and investigation of a novel precast beam-column friction hinge joint enhanced with Cu–Al–Mn SMA-plate-based self-centring buckling-restrained devices