Abstract:For an anisotropic thin-walled tube without changing its circular geometry, only the experimental data of initial yield and subsequent plastic deformation along the axial and circumferential directions can be obtained till now. These experimental data are not sufficient to construct an anisotropic constitutive relation for simulations of tube deformation processes. A novel shear test of tubular materials is proposed to achieve the state of shearing plastic deformation along the axial direction of thin-walled tubes. Two semi-circle mandrels and one specially designed tubular specimen are used in the shear experiment. Optimizations of the specimen shape and mandrel structure were carried out by using FE simulation. The influence of the specimen shape, such as the length of the shear zone and the length of the axial slot, on the stress state of the shear zone was discussed. A thin-walled 5052 aluminum tube was used in the shear experiment using the optimized specimen shape. To understand the corresponding relationship between the tensile properties and the shear properties of an anisotropic tube, the uniaxial tension stress-strain relationship was equivalently transformed to the shear stress-stain relationship using the Mises, Tresca, Hill48, and Barlat-lian constitutive functions. After optimizing the specimen shape, the shearing condition of the tested tube is closer to the pure shear stress state. Based on the tests, the pure shear stress state can be maintained to a large deformation extent. The experimental shear stress-strain relationship was compared with the converted stress-strain relationship based on the uniaxial tension tests using the Mises, Tresca, Hill48, and Barlat-lian constitutive functions. The results show a large difference between the transformed stress-strain relationship and the shear stress-strain relationship. This testing method can provide necessary empirical data with the principal stress directions along the direction at an angle of 45° to the tube axis. The shear plastic deformation properties of some anisotropic materials cannot be equivalently described by the experimental data of the tensile test. The shearing characteristics obtained by this novel experimental method can be applied to the characterizations of anisotropic constitutive relations for simulations of tube deformation processes.

Investigation into the Shear Effect of Torsion Extrusion Process

A New Wavy Cross-Sectional Torsion Extrusion Method with an Application to Improve the Mechanical Properties of an Aluminum Matrix Composite

Particle Dispersion and Grain Refinement of In-Situ TiB2 Particle Reinforced 7075 Al Composite Processed by Elliptical Cross-Section Torsion Extrusion

Strength and Ductility Improvement of an In-Situ TiB2/Al–Zn–Mg–Cu Composite by Elliptical Cross-Section Torsion Extrusion

Mechanisms of Simultaneously Improving the Strength and Ductility of an In-Situ Tib &Lt;sub>2</sub>/al-Zn-mg-cu Composite by Elliptical Cross-Section Torsion Extrusion

Influence of extrusion method on the microstructure and mechanical properties of formed magnesium alloy tubes

Effects of Extrusion Ratio on Microstructural Evolution and Mechanical Behavior of in Situ Synthesized Ti-6Al-4V Composites

Improving mechanical properties of AZ31 alloy sheets via novel turned-bearing extrusion by introducing shear strain

Study of Microstructure and Mechanical Properties by Torsional Behavior in Axial Closed Die Rolling Forming

Study on the shear-torsion deformation of rotary tube piercing process for nickel base superalloy

Modeling and finite element simulation of polypropylene behavior under severe plastic deformation by high-pressure torsion

Optimizing Pure Shear Experiment to Properly Characterize the Shear Properties of Thin-Walled Aluminum Alloy Tubes

Superplastic Behavior of an In-Situ TiB2 Particle Reinforced Aluminum Matrix Composite Processed by Elliptical Cross-Section Torsion Extrusion

Heat Transfer and Viscous Polymer Melting Capacity Correlation in Self-Controlled Torsion Induced Extrusion

Microstructure Evolution and High-Temperature Tensile Behavior of the Powder Extruded 2.5 Vol% TiBw/TA15 Composites

Experimental characterization and numerical analysis of 3D woven preforms torsional deformation

An extrusion−shear−expanding process for manufacturing AZ31 magnesium alloy tube

Mechanisms Behind the Superplastic Behavior of As-Extruded Tibw/Ti6al4v Composites with A Network Architecture

Investigation on Anisotropic Mechanical Behavior of Ti-6Al-4V Alloy Via Schmid Factor and Kernel Average Misorientation Distribution

Process Design and Microstructure-Property Evolution During Shear Spinning of Ti2AlNb-based Alloy

The Effects of Severe Torsion on Microstructure, Texture, and Mechanical Properties of a Pure Nickel Rod