Abstract:High-performance thermoplastics like polyetheretherketone (PEEK), with their outstanding thermal stability, mechanical properties and chemical stability, have great potential for various structural applications. Combining with additive manufacturing methods extends further PEEK usage, e.g., as a mold insert material in polymer melt processing like injection molding. Mold inserts must possess a certain mechanical stability, a low surface roughness as well as a good thermal conductivity for the temperature control during the molding process. With this in mind, the commercially available high-performance thermoplastic PEEK was doped with small amounts of carbon nanotubes (CNT, 6 wt%) and copper particles (10 wt%) targeting enhanced thermomechanical properties and a higher thermal conductivity. The composites were realized by a commercial combined compounder and filament maker for the usage in a material extrusion (MEX)-based 3D-printer following the fused filament fabrication (FFF) principle. Commercial filaments made from PEEK and carbon fiber reinforced PEEK were used as reference systems. The impact of the filler and the MEX printing conditions like printing temperature, printing speed and infill orientation on the PEEK properties were characterized comprehensively by tensile testing, fracture imaging and surface roughness measurements. In addition, the thermal conductivity was determined by the laser-flash method in combination with differential scanning calorimetry and Archimedes density measurement. The addition of fillers did not alter the measured tensile strength in comparison to pure PEEK significantly. The fracture images showed a good printing quality without the MEX-typical voids between and within the deposited layers. Higher printing temperatures caused a reduction of the surface roughness and, in some cases, an enhanced ductile behavior. The thermal conductivity could be increased by the addition of the CNTs. Following the given results, the most critical process step is the compounding procedure, because for a reliable process–parameter–property relationship, a homogeneous particle distribution in the polymer matrix yielding a reliable filament quality is essential.

3D Printing of High-Stiffness and High-Strength Glass Fiber Reinforced PEEK Composites by Selective Laser Sintering

High Temperature Rheological Behavior and Sintering Kinetics of CF/PEEK Composites During Selective Laser Sintering

Superior strength in the 3D ‐printed polyether‐ether‐ketone composites reinforced by annealing and carbon fibers

Influence of Process Parameters on the Interlaminar Shear Strength of CF/PEEK Composites In-Situ Consolidated by Laser-Assisted Automated Fiber Placement

Preparation of short CF/GF reinforced PEEK composite filaments and their comprehensive properties evaluation for FDM-3D printing

High-performance carbon fiber reinforced polyether-ether-ketone composite pellets 3D-Printed via screw-extrusion additive manufacturing

Bi-scale Interfacial Bond Behaviors of CCF/PEEK Composites by Plasma-Laser Cooperatively Assisted 3D Printing Process

Process Study of Selective Laser Sintering of PS/GF/HGM Composites

Poly Ether Ether Ketone and Its Composite Powder Prepared by Thermally Induced Phase Separation for High Temperature Selective Laser Sintering

High-strength carbon fiber-reinforced polyether-ether-ketone composites with longer fiber retention length manufactured via screw extrusion-based 3D printing

Interlayer bonding improvement of PEEK and CF-PEEK composites with laser-assisted fused deposition modeling

3D-Printed high performance PEEK/CF-PEEK polymer composites—An investigation on microstructural characteristics and mechanical performance

A novel printing strategy to fabricate polyetheretherketone (PEEK)-based composites via hollow filaments filled with multiple reinforcements

Mechanical Properties Optimization of Poly-Ether-Ether-Ketone Via Fused Deposition Modeling.

Effects of FDM-3D printing parameters on mechanical properties and microstructure of CF/PEEK and GF/PEEK

The Optimization of Process Parameters and Characterization of High-Performance CF/PEEK Composites Prepared by Flexible CF/PEEK Plain Weave Fabrics

Impregnation and Interlayer Bonding Behaviours of 3D-Printed Continuous Carbon-Fiber-reinforced Poly-Ether-ether-ketone Composites

Mechanical properties, biosafety, and shearing bonding strength of glass fiber-reinforced PEEK composites used as post-core materials

Material Extrusion 3D Printing of PEEK-Based Composites

Enhancing the mechanical properties of SCF/PEEK composites in FDM via process-parameter optimization

Selective Laser Sintering Parameter Optimization of Prosopis Chilensis/Polyethersulfone Composite Fabricated by AFS-360 SLS