Abstract:Lattice structures are emerging as highly effective heat exchange mediums in exchangers and radiators due to their low weight, high specific stiffness and strength, and extensive surface area. These attributes render them particularly suitable for enhancing heat transfer efficiency while maintaining a lightweight and structurally sound design. Certain applications, such as hot stamping, demand both high heat transfer performance and significant load-bearing capacity. Arch micro-strut (ARCH) lattice is a kind of high load-bearing lattice. Currently, there is a gap in the research on its heat transfer performance. This study provides a comprehensive analysis of the heat transfer and mechanical performance of additively manufactured ARCH lattice structures. Deionized water (DI water) was selected as the working fluid in this study. The analysis spans various relative densities, inlet velocities, array orientations, and gradient configurations, employing both experimental and simulation approaches. The results of this study reveal that as relative density increases, the pressure drop gradually rises, while the convective heat transfer coefficient increases before stabilizing. The pressure drop reaches a maximum of 348 kPa at 4 m/s, 40 % relative density, and the convective heat transfer coefficient reaches a maximum of 13,805 W/m2·k at 4 m/s, 20 % relative density. At a relative density of 20 %, the convective heat transfer coefficient reaches its maximum at the same inlet velocity. Specifically, at an inlet velocity of 4 m/s, the convective heat transfer coefficient for a 20 % relative density is 115 % higher than that at 0 %. The maximum Von Mises stress and deformation decrease progressively as relative density increases, from 980.72 MPa to 236.05 MPa, suggesting a substantial enhancement in the compressive properties of the structure. Additionally, a higher inlet velocity results in an enhanced convective heat transfer coefficient. The convective heat transfer coefficient increased by an average of 2300 W/m2·k when the flow rate increased from 1 m/s to 4 m/s. The anisotropic nature of ARCH lattice structure significantly affects mechanical properties and heat transfer efficiency, with the heat transfer coefficient being higher at the inlet along X-direction compared to Z-direction, and a lower pressure drop in X-direction. The gradient structure is shown to effectively address the non-uniform heat dissipation requirements of various components. Specifically, decreasing gradient (DG) configuration offers superior heat transfer performance under similar pressure drop conditions, while increasing gradient (IG) configuration provides better temperature uniformity. Overall, ARCH lattice structure demonstrates superior performance compared to face-centered cubic with vertical strut (FCCZ) structure, with an efficiency index approximately 200 % higher than that of FCCZ structure.

Topology Review and Convective Heat Transfer Comparison of 3D Lattice Structures

Additive manufactured high-performance topology-optimized lattice structure: Compressive behavior and flow heat transfer characteristics

Fluid flow and heat transfer performance for micro-lattice structures fabricated by Selective Laser Melting

Review and comparison of turbulent convective heat transfer in state-of-the-art 3D truss periodic cellular structures

Convective heat transfer in I-shape heat sink under the action of Lorentz force via LBM

Study on heat dissipation performance of a lattice porous structures under jet impingement cooling

Topological design of open-cell microstructure with optimal effective thermal conductivity

Comparing endwall heat transfer among staggered pin fin, Kagome and body centered cubic arrays

Phase change heat transfer enhancement based on topology optimization of fin structure

Evaluating Lattice Mechanical Properties for Lightweight Heat-Resistant Load-Bearing Structure Design

Analyzing heat transfer performance of ARCH lattice microchannel heat exchanger fabricated using selective laser melting

Experimental study of heat transfer in a rectangular cell with built-in lattice channels

Effects of different cross-sections of Body Centered Cubic cells on pressure drop and heat transfer of additively manufactured heat sinks

Heuristic optimality criterion algorithm for topology optimization of conjugate heat transfer problem

Influence of design parameters on natural convection heat transfer in additively manufactured body centered cubic lattice structures

Effects of Lattice Orientation Angle on TPMS-Based Transpiration Cooling

Heat Dissipation Design Based On Topology Optimization And Auxiliary Materials

Analysis on the convective heat transfer process and performance evaluation of Triply Periodic Minimal Surface (TPMS) based on Diamond, Gyroid and Iwp

Simulation and Experimental Study on Flow and Heat Transfer Performance of Sheet-Network and Solid-Network Disturbance Structures Based on Triply Periodic Minimal Surface

Topology Optimization of Turbulent Forced Convective Heat Sinks Using a Multi-Layer Thermofluid Model

Optimization design and experimental research on cooling performance of U-shaped latticework cooling structure with perforations used for gas turbine blade